Binding Mount Paper Templates

[AlpiNord]

Does anyone have a paper template for Tyrolia attack demo bindings?

thanks

Here ya go: Tyrolia Attack Demo

[Duffman]

Any template for the Tyrolia Sx junior bindings?

[GravityDT]

Anyone have a template for the new ATK Crest 10 ?? Hoping to mount wifey’s new setup this wkd. TIA

[esseff]

Looking for mount point on the new M7 Mantra (177). I've seen -12 but other conflicting info as well.

[AlpiNord]

Anyone have a template for the new ATK Crest 10 ?? Hoping to mount wifey’s new setup this wkd. TIA

Here is the Crest 10 Template from ATK: https://www.slidewright.com/Bindings...-crest8-10.pdf
or the composite 'Universal' ATK Template https://www.slidewright.com/Bindings...K_Template.pdf .

[bearcub69]

can anyone confirm that the fks/look pivot template will center up on the adjustment range for the new pivot 2.0?

I know the hole pattern is the same, just want to make sure I won't be on either end of the adjustment range when mounting for my bsl

[cooltsi]

Anyone point me to the Dynafit Speed 12 of late. Toe matches the radical but the heel plate the real heel adjusts on is a much shorter pattern versus any I can find.


Sent from my iPhone using TGR Forums

[bearcub69]

can anyone confirm that the fks/look pivot template will center up on the adjustment range for the new pivot 2.0?

I know the hole pattern is the same, just want to make sure I won't be on either end of the adjustment range when mounting for my bsl

answering my own question..

although the hole pattern is the same, it doesn't look like the current fks template works with the pivot 2.0 flawlessly in terms of centering up on the adjustment range and mounting exactly where you want it..

just did a test run and the boot center was forward of the line I wanted. every pair of 1.0s ive mounted up have been right where I wanted them.
also had to tighten the arms more forward of the middle knurl to get forward pressure right.

what's the short term solution? set the template to a 5mm shorter bsl? hopefully someone can get us an updated 2.0 template

[Hookitlow]

I just mounted some strive 12s and was trying to use the Knut warden 11 template, but read and then confirmed that the spacing/bsl was way off. I found a pretty bare bones one but I like the layout of the Knut/powder guide one as it was easier to line up the toe and heel sides. Does anyone know of an updated or verified warden11/strive 12/14 template?

[~mikey b]

looking for template for Dynafit Ridge and 7 Summits

[AlpiNord]

Need dimensional confirmations on:
-hole layouts
-pin & heel locations
-relative BSC/BSL

[~mikey b]

thanks Terry

I’ll have the lad that’s doing the mount confirm with you

[AlpiNord]

While I'm in the mode, Dynafit Speed/Speedfit

Need dimensional confirmations on:
-hole layouts
-pin & heel locations
-relative BSC/BSL

[cooltsi]

While I'm in the mode, Dynafit Speed/Speedfit

Need dimensional confirmations on:
-hole layouts
-pin & heel locations
-relative BSC/BSL

Working on it. I mounted some yesterday but had to tweak forward on the heel to avoid another set of heel hole conflicts.


Wandering the halls with no passTGR Forums

[jgrule83@gmail.com]

Anyone have a template for Marker Kingpin M-Werks 12? Will any Kingpin template work? Not finding much specific to the M-Werks online.

[TexasGortex]

I just mounted some strive 12s and was trying to use the Knut warden 11 template, but read and then confirmed that the spacing/bsl was way off. I found a pretty bare bones one but I like the layout of the Knut/powder guide one as it was easier to line up the toe and heel sides. Does anyone know of an updated or verified warden11/strive 12/14 template?

I also always used Knut's template and need to mount Strive 14 GW. How much did you find the BSL off? I just did a quick measurement and Knut's Warden 11 appears to match SlideWright's Strive 12/14. The Salomon technical manuals suggest the Warden 11 MNC should match the Strive 12/14 GW, so I would assume if one template is off they both are.

AlpiNord, I'm a little confused by the SlideWright comparison PDF. Toe pieces #8 and 9 (counting down from top) are both labelled "Warden 11 & 13" except #8 has a width of 30mm and #9 40mm. Should #8 be labelled "Warden 11" and #9 "Warden 13" or are they both supposed to be 40mm wide?

[AlpiNord]

I'm in the same boat. I really liked Knut's layout and need to mount Strive 14 GW. How much did you find the BSL off? I just did a quick measurement but Knut's Warden 11 appears to match SlideWright's Strive 12/14. The Salomon technical manuals suggest the Warden 11 MNC should match the Strive 12/14 GW, so I fear they may both be off on BSL.

AlpiNord, I'm a little confused by the SlideWright comparison PDF. Toe pieces #8 and 9 (counting down from top) are both labelled "Warden 11 & 13" except #8 has a width of 30mm and #9 40mm. Should #8 be labelled "Warden 11" and #9 "Warden 13" or are they both supposed to be 40mm wide?

I'll circle back to this later.

'Way off' is not a number please quantify relative to toe of boot to rear toe holes and heel of boot relative to forward holes of heel pieces at mid adjustment range.

Good catch on the incorrect 30mm dimension it is drawn and 40mm and I revised it. Please repeat this in the Salomon hole layout thread to keep it more together. Check out the Minimum & Maximum Boot Sole Lengths thread. I thought this was vetted for the Wardens and the binding layout tool we've sold has had zero complaints.



Sometimes you'll need to make adjustments because none of this is perfect. Perform a test mount, measure adjustments and provide what they are if you find any to help others.

Also, check out DIY Binding Templates for more info to make your own or simply figure out hole layouts relative to BSCs.

[TexasGortex]

I'll circle back to this later.

'Way off' is not a number please quantify relative to toe of boot to rear toe holes and heel of boot relative to forward holes of heel pieces at mid adjustment range.

Good catch on the incorrect 30mm dimension it is drawn and 40mm and I revised it. Please repeat this in the Salomon hole layout thread to keep it more together. Check out the Minimum & Maximum Boot Sole Lengths thread. I thought this was vetted for the Wardens and the binding layout tool we've sold has had zero complaints.

[IMG]https://www.slidewright.com/Bindings/Binding_Layout_Tool/STH2/Warden_dims.png[IMG]

Sometimes you'll need to make adjustments because none of this is perfect. Perform a test mount, measure adjustments and provide what they are if you find any to help others.

Also, check out DIY Binding Templates for more info to make your own or simply figure out hole layouts relative to BSCs.

I edited my post for clarity; I did not have a "way off" BSL, I wanted more info on his problem. I was just trying to start with a solid template to save some time and 2x4s. I didn't buy new bindings for a couple years and selecting the right template got a lot more complicated! Might be time to buy your tools.

Thanks for the links. I bookmarked this thread ages ago and didn't think to look elsewhere.

[TexasGortex]

I confirmed the Knut and SlideWright templates are accurate with the caveat that it defaults to the smallest end of the adjustment range. I would recommend a test mount before considering if you want adjustments (for instance, this would be perfect for a growing kid likely to get new boots). It will work as is.

[AlpiNord]

I confirmed the Knut and SlideWright templates are accurate with the caveat that it defaults to the smallest end of the adjustment range. I would recommend a test mount before considering if you want adjustments (for instance, this would be perfect for a growing kid likely to get new boots). It will work as is.

Good to know. How far to the middle of the adjustment range and it’s total?

(The ‘way off’ comment was in response to the post you quoted.)

Sent from my iPad SlideWright Ski & Snowboard Tools

[AlpiNord]

@~mikey b Here's the Dynafit Ridge & Seven Summits+ template to confirm.

[davidgarrison4@live.com]

Hey there, sorry if this has been posted but I just recieved my Salomon S/lab Shift 2 bindings and with the orginial shift template it looks like the toe piece bolt spacing has been updated, if I slide the toe piece all the way back on the front mounting tap I about 8-10mm off the four mounting screws and the front two are about 1.5mm too narrow.as well as the bsl is about 10 mm behind center. I also noticed that the rear mounting plate puts me toward the front end of the adjustment range. I just wanted to see if anyone has had any first hand expierence with the updated bindings before I just lay it out freehand.

Thanks again for this resource!

[Skinnog]

Hi all,
Looking for a template for the Marker Alpinist FREE - the latest pin binding from Marker, new for the 24/25 season (wider mounted version of the Alpinist for bigger skis).
Going to have to DIY as none of my local shops have the jig and I've got a trip booked in two weeks.
Hoping someone can help!
Thanks!

[Hookitlow]

Hey there, sorry if this has been posted but I just recieved my Salomon S/lab Shift 2 bindings and with the orginial shift template it looks like the toe piece bolt spacing has been updated, if I slide the toe piece all the way back on the front mounting tap I about 8-10mm off the four mounting screws and the front two are about 1.5mm too narrow.as well as the bsl is about 10 mm behind center. I also noticed that the rear mounting plate puts me toward the front end of the adjustment range. I just wanted to see if anyone has had any first hand expierence with the updated bindings before I just lay it out freehand. Thanks again for this resource!

So I did some homework when I first got a shift2. The shop that mounted my first one said the jig is the same. When I took that binding off, I confirmed that with the toe piece on the center lug, you can slide the toe piece back 3mm (my best estimation) past the holes for the other 4 screws. Other than that, everything else on my mount with knuts template on the next ski worked perfect. I left the holes in the exact spot as the template, thinking that 1 if a shop does it like this there is probably something I don't know going on in there and that 2 that something might be some play left in the system when using the pins and locking lever perhaps?Also did you double check the printing scale? sounds like it printed too small.

[Hookitlow]

I also always used Knut's template and need to mount Strive 14 GW. How much did you find the BSL off? I just did a quick measurement and Knut's Warden 11 appears to match SlideWright's Strive 12/14. The Salomon technical manuals suggest the Warden 11 MNC should match the Strive 12/14 GW, so I would assume if one template is off they both are. AlpiNord, I'm a little confused by the SlideWright comparison PDF. Toe pieces #8 and 9 (counting down from top) are both labelled "Warden 11 & 13" except #8 has a width of 30mm and #9 40mm. Should #8 be labelled "Warden 11" and #9 "Warden 13" or are they both supposed to be 40mm wide?

Next time Im messing with one Ill see if i can put a number to it. From what i can remember the toe piece and midsole were perfect, but as was stated, the heel piece was off as far as adjustment goes. I have a 27.5 and could probably get a 29.5 in with how much adjustment was there, but not a 26.5, so yes, it wasnt centered.

Here is what I wound up using as to not mess around until i sorted it out.

https://github.com/tomahawkins/bindi...omon-warden-11