Binding Mount Paper Templates

[retirwntm]

Anyone have a resource for a beast 16 template? There's one for Stockholm reviews but I'm either MR or it's not scaled correctly.

[Videogroove]

Thanks for reply, now everything is clear with these bars and I have another question:

If FKS/Pivot 14 are correctly adjusted for current boots/BSL is it normal that ski-brakes have some movement (very little lift up and down) when skier try to move boot/heel up and down (of course when foots with boots are set in bindings)?

[sdsimo3]

Hello all I just purchased the Look SPX 12 fluid bindings. I am wondering if anyone knows if these match a template on here. I thought maybe the Look axial2, but not sure.

Also How difficult is the mounting process. I have never done it, but am looking to start mounting and waxing my own skis. I have worked as a carpenters hand for a few summers and am quite capable with tools. Just wondering if it's a task I can tackle or not worth risking my new skis and bindings? Any help or advise would be great!

Thanks in advance

[Knut]

Hello all I just purchased the Look SPX 12 fluid bindings.

They are the same than the new axial3. Which are different than the axial2, if I'm not mistaken.
I yet haven't mounted one of those myself, and I am not aware of an existing template

Also How difficult is the mounting process. I have never done it, but am looking to start mounting and waxing my own skis. I have worked as a carpenters hand for a few summers and am quite capable with tools.

You should have no difficulties, then. Given the right choice of mounting beverage, that is.

[Meadow Skipper]

See Radical 2.0 template above (and G3 ION, below) as a heel line example and template links. I can provide measurements for heel locations relative to the Jigrex plates we have in stock if needed.

G3 ION template:

This worked perfectly. Thanks Terry! I owe you beer/brown liquor:

[AlpiNord]

Good to know. I'll get down there for a beer one of these days. Nice color coordination.

[Videogroove]

Guys, If ski-master found that screws that mount bindings to skis (heel pieces in my case) not tighten enough (they were mounted 2 years ago in shop where I bought it) and he little tight it now it is right decision?

Can it damage the waterproof in holes/screws?

It is usual practice in ski-service to tight screws if found that they are not tight properly?

Do I need to check toe-pieces and also little tight it if it is possible?

Thanks in advance for replies!

[mall walker]

This is probably already answered somewhere... but do the Speed Turn 2.0 and Speed Radical share the same heel hole pattern?

Specifically, I am trying to fit into a heelpiece drilled with inserts for Speed Radicals, can I use a Speed Turn 2.0 binding?

[NW_SKIER]

Struggling to find a mount template for the warden mnc demo. Anybody have a link?

[liv2ski]

That's a cool idea. Mind sharing where that line is in reference to the 4 holes? Have you done the math to get the line in exactly the right spot - in other words, should I add what you've done to the template?

I was looking for a sth2 wtr template today and found one on this page. http://www.slidewright.com/ski-bindi...to-powderguide I will mount it up tomorrow on a 2X4 to make sure before drilling my new skis.

Edit to add, this template did was waaaay short on the boot center measurement, so if you use it, mount to a 2X4 first to be sure you have it correct. I mean, I guess I could have fucked up, but I don't think so.

[bfly]

Thanks tBatt for the template. Just mounted a pair of Vipecs and it was spot on.

BTW, the template on Slidwright and Powderguide is not correct at this time. (3/25/2016).

[Wapow]

Take this for a whirl. Please let me know how it goes after a test mount.

The Radical 2.0 template worked great, thanks!

[number nine]

I'm mounting up a new pair of dps 112 rpc with solly 900 and dalbello krypton pros. During the process I've noticed that the boot mark is @ 5 mm back from the measured center . I'm not sure if this is an error on dalbellos part or if for some esoteric reason they want me to use that point . If anyone has encountered this issue I would greatly appreciate any input

[number nine]

^^^^^^ Uh never mind .I folded the paper the wrong way

[handlebarsfsr]

Anyone know where to find templates for a tyrolia attack 13 demo or a rossignol axial 3?

[Meadow Skipper]

Anyone know where to find templates for a tyrolia attack 13 demo or a rossignol axial 3?

The template for the Rossi Axial 2 on the first page works fine for the Axial 3.

http://www.tetongravity.com/forums/s...24#post4544724

[Knut]

BTW, the template on Slidwright and Powderguide is not correct at this time. (3/25/2016).

I'd be curious to know what is incorrect about the Vipec template, as I have had only positive feedback up to now and people verifying it.

Thanks for helping to improve the templates further

[handlebarsfsr]

The template for the Rossi Axial 2 on the first page works fine for the Axial 3.

http://www.tetongravity.com/forums/s...24#post4544724

Thanks. I had read conflicting information saying the heels were a different pattern.

[bfly]

I'd be curious to know what is incorrect about the Vipec template, as I have had only positive feedback up to now and people verifying it.

Thanks for helping to improve the templates further

The spacing on the holes were too close.

I used Inkscape to overlay the two templates. You can see they are off when they are overlaid in the same document. I also printed out the template and did a test mount on a 2x4.

The red circles are the hole locations for the Powderguide template:

[j0z77]

Take this for a whirl. Please let me know how it goes after a test mount.

worked perfect.
sorry for the delay.

[AlpiNord]

Good to know. Thanks. We'll consider it vetted then.

[zartagen]

Anyone know where to find templates for a tyrolia attack 13 demo or a rossignol axial 3?

I found an elan technical manual pdf online that had a part number for a paper template for the attack 13s. Does anyone have one of those that they can post or know how to order one?

[ski-wpk]

anyone have a black diamond 01 template? i know one comes in the box but i'm mounting a used pair and can't find a template anywhere online. thanks.

[Meadow Skipper]

anyone have a black diamond 01 template? i know one comes in the box but i'm mounting a used pair and can't find a template anywhere online. thanks.

I'm pretty sure that the 4-hole template from G3 will work for the front and back holes. If you have the 6 hole O1, and the 4 holes match (test it) then you can pencil-whip in the 2 middle holes.
http://cascadeclimbers.com/forum/ubb...mplates_AT_and

And I think there are templates in the 'G3 Learning Center' at www.genuineguidegear.com, but the website seems a little menstrual at the moment. Check later.

[ski-wpk]

I'm pretty sure that the 4-hole template from G3 will work for the front and back holes. If you have the 6 hole O1, and the 4 holes match (test it) then you can pencil-whip in the 2 middle holes.
http://cascadeclimbers.com/forum/ubb...mplates_AT_and

And I think there are templates in the 'G3 Learning Center' at www.genuineguidegear.com, but the website seems a little menstrual at the moment. Check later.

Thanks. The G3 template worked for BD01s. G3 holes are front and middle holes on BD01s. Back holes are 3cm back from middle.