The chainsaw thread...

[Bronco]

For those of you with Milwaukee saws, Westcoast Saw is selling after market dogs that actually work for $17.00. Pretty nice Upgrade: https://westcoastsaw.com/products/we...43881895297254

[XXX-er]

Yeah for firewood cutting I'd go gas every time. I love my dual 18v Makita saw for homeowner and light trail clearing use, though. I cut through a 24" downed tree on 2 sets of batteries once. (2 full cuts to remove a section.)

exactly ^^ what happened up at the area last season, after a good storm there are 3 big stems down so buddy does 4 cuts on 2 of them and had to come back for the last one

[SoVT Joey]

2 out of 6 of my m18 12amp batteries just died. 2 and a half years old. Almost $600 to replace those two.

For the $1000 it will cost to get into an electric saw and batteries, go buy a stihl ms 362 or a ms 261. The 261 will do just about anything you need, it’s light and fast. That’s my go to saw for a lot, also for my brother and another buddy that both have tree businesses. They both have probably 10-15 saws each and the 261 is always with them

Biggest mistake is buying a homeowner level saw and expecting it to last. The pro series can have the case cracked and piston replaced if needed. The homeowner saws are pretty much throw away.


Sent from my iPhone using Tapatalk

[XXX-er]

Yeah ^^ I cut a bunch of ski run with the 261, I would run it for 5-6 hrs straight, I think it drinks a little less fuel than the 361 and its lighter which is important fo a small azn man packin all his gear up a mtn

Homeowner saws are 1/3rd the price of a pro saw and they all look the same SO how it works with the homeowner saw is buddy buys one way cheaper than a 261 probably for 1/3rd of the price, runs it hard so it dies pretty quick so he buys another one and another one, by the time he figures it out he has been thru 2 or 3 saws and still hasn't got a good working saw

Whereas if he spent the bucks for a pro saw in the end he would have spent the same $$$$, buy once buy right, my kid will inherit the 261 and it will still be running fine

[SoVT Joey]

Yeah ^^ I cut a bunch of ski run with the 261, I would run it for 5-6 hrs straight, I think it drinks a little less fuel than the 361 and its lighter which is important fo a small azn man packin all his gear up a mtn

Homeowner saws are 1/3rd the price of a pro saw and they all look the same SO how it works with the homeowner saw is buddy buys one way cheaper than a 261 probably for 1/3rd of the price, runs it hard so it dies pretty quick so he buys another one and another one, by the time he figures it out he has been thru 2 or 3 saws and still hasn't got a good working saw

Whereas if he spent the bucks for a pro saw in the end he would have spent the same $$$$, buy once buy right, my kid will inherit the 261 and it will still be running fine

Bingo. My dad still has a 034 that runs great still, he got it before I was born when my parents were building the house 40 years ago.

And the 362/361 is so much heavier then the 261. Exact same reason I use my 261 so much.

Sent from my iPhone using Tapatalk

[XXX-er]

i don't have any tools with batteries and the extension cords seem to last forever if I don't run over them, I mentioned my lack of powertool cred to a carpenter bud and he said well it sounds like you don't need any more than what you got, if you do need more for a job or sft then you just go out and buy them

[SoVT Joey]

i don't have any tools with batteries and the extension cords seem to last forever if I don't run over them, I mentioned my lack of powertool cred to a carpenter bud and he said well it sounds like you don't need any more than what you got, if you do need more for a job or sft then you just go out and buy them

I have tons of battery Milwaukee, but I’m on a lot sites with no power yet or really far from an outlet. If I am on a site with power, I’ll run my corded skilsaw and grinder over my battery ones every time. I have both 7” grinders, the corded one is almost impossible to stop it when pushing down hard on a blade, the battery will shut down and if you try to over work it, a 12amp will be dead in 20 minutes. But I have to have both options cause I get sick of listening to a generator run all day.

I feel like all of my batteries are losing power, not just the two that died. And none are more than 6 years old. Pretty shitty life expectancy at the price of them.


Sent from my iPhone using Tapatalk

[toast2266]

For the $1000 it will cost to get into an electric saw and batteries, go buy a stihl ms 362 or a ms 261. The 261 will do just about anything you need, it’s light and fast. That’s my go to saw for a lot, also for my brother and another buddy that both have tree businesses. They both have probably 10-15 saws each and the 261 is always with them

Yup. Although if / when I buy another firewood saw, it'll be a 362. For bucking up firewood, the bit of extra weight over the 261 isn't the end of the world - I'm not lugging the saw all over the place, and I get a fair amount of 20"+ Doug fir where the extra power of the 362 would be nice. I could run a full comp chain on a 24" bar, whereas the 261 would probably need a skip tooth and even then would maybe bog a bit.

Sent from my SM-S901U using Tapatalk

[SoVT Joey]

Yup. Although if / when I buy another firewood saw, it'll be a 362. For bucking up firewood, the bit of extra weight over the 261 isn't the end of the world - I'm not lugging the saw all over the place, and I get a fair amount of 20"+ Doug fir where the extra power of the 362 would be nice. I could run a full comp chain on a 24" bar, whereas the 261 would probably need a skip tooth and even then would maybe bog a bit.

Sent from my SM-S901U using Tapatalk

I have my 25” bar on my 362 and never take it off. But I’d make the same choice as you for cutting fire wood only. A 20” bar with a skip and a half chain and short rakers would eat softwood like butter


Sent from my iPhone using Tapatalk

[XXX-er]

I just ran stock sthil chain but the big thing is a very sharp chain . I'm there to run saw not sit in the snow filing chains so I would carry 2 or 3 and just swap the chains

https://www.amazon.ca/dp/B0002ZY1WG?...=camdenxodl-20

I have an Oregon version of this ^^ Jig and it did a great job, I would file chain in the comfort of my shop while having a beverage, mine only cost me 20$ on FB market but a good jig is worth the $$$ IME

https://www.outdoorlife.com/gear/bes...aw-sharpeners/

this ^^ site rated the Granberg best overall which is suprising i thot an electric sharpener would do a better job

[neufox47]

I'm looking for a battery saw to cut lots of firewood. Power, battery life and short charge time are my main criteria, as well as being modular so I can eventually get a mower or other tools. After some reading of this thread and other research, these are on the list:
-Greenworks GS181
-Ego Power+ CS 1800
-Ego Power+ CS 2005
-Greenworks Pro 8V
-Echo DCS 5000
What else should I be looking at?

I think the comments on gas vs electric for heavy work are still accurate but people comparing a 18v Milwaukee to an 82v Greenworks that puts out 2.7kw with a 360 wh battery is apples to oranges. But 2700/360 gives a theoretical max run time of 7.5 minutes at full throttle.

[XXX-er]

Yup. Although if / when I buy another firewood saw, it'll be a 362. For bucking up firewood, the bit of extra weight over the 261 isn't the end of the world - I'm not lugging the saw all over the place, and I get a fair amount of 20"+ Doug fir where the extra power of the 362 would be nice. I could run a full comp chain on a 24" bar, whereas the 261 would probably need a skip tooth and even then would maybe bog a bit.

Sent from my SM-S901U using Tapatalk

Yeah the 261 is or was the smallest pro-grade saw but the 362 is where you get 60cc vs 50 cc/ 3/8th chain as opposed to .325/ dogs/ a full wrap handle/ possibly a heated handle is available ... all of which is probably what weighs more

I used a 361 bucking fire wood for 5 yrs at a place i was care-taking, where I learned how to not sharpen chains very well ... which is why I got the good jig

[bodywhomper]

I first got an ms361 (used) then a new ms241, which is no longer sold in the US from what I can tell. The ms241 was a delayed housewarming gift and it was selected over an ms261 because it was lighter and had a bigger difference in power from the ms361. With the non-safety pico chain, the ms241 rips. Three in my household use the ms241. My oldest kid and I use the ms361.

[mcski]

Cool. Come by and cut down some of the trees behind my house. We can put our ACLs to the test getting out of the way

[bodywhomper]

Haha. Your knee will be fine! Unfortunately, I have plenty of saw work at home. Luckily, I’m not felling any cat faced burned out hazard trees.

[XXX-er]

261 was smallest pro saw when i bought it, the 241 came out in the next year or 2 but I don't see it in the lineup anymore up here, on google I found

" The 241 is no longer for sale in North America because they likely didn’t want it to compete with the similar MS 261, and the two were too close in price. However, the 241 is still being produced and sold in other locations, such as the United Kingdom."

[bodywhomper]

It looks like stihl has a 201 in a rear handle (~35cc). I’m not sure if that’s a higher end saw. I thought the 20cc difference between my saws was about right.

I’d love to mod the muffler on my ms241 to get a little more juice out of it. It was very simple (formulaic) for my ms361. I haven’t figured out an easy spark arrester that’ll work with a simple ms241 muffler mod.

[Truckee Joe]

I just process a fare amount of wood and fall big trees around the property all the time. I have a 460, I call her old reliable. Seriously I never tune it, starts all time even in freezing temps. She does drink a lot but I don’t care, gives me an excuse to take a break.
I have a 028 also, I find the older saw has lots of low end torque and it also runs like a champ, but I do have to clean it out more often. Wife uses a husky rancher, I don’t really like it because it will only run good for the first tank of gas. Once it gets hot I just can’t seem to keep it running.

[XXX-er]

Somebody gave my kid one of those sthil with the top handle only and i used it on a bike trail blow down, it was older, did not have a wrap around handle just the top handle so that was wierd trying to get any pressure on the bar, pictures on line show a half handle with the top handle

yer 028 is all metal is 47cc so about the same size engine as the 50cc 261

the 460 is a 76cc pro saw i know a local pro logger who has 3 of the 461 , he got them all Walkerized for more power sez they are are the best saws he has ever used

some of those cheap homeowner saws have plastic engine cases which is I think why they can't rev out as high