Results 1 to 25 of 71
Thread: Aluminium rims stuck to hubs
-
04-25-2022, 06:42 PM #1Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,043
Aluminium rims stuck to hubs
Tacoma rims stuck on the hubs from corrosion, the tire dealer no longer swaps them for free so I just realized this was happening while swapping them myself and that I could get stuck out there unable to get a flat tire off, anybody dealt with this ?
today on the summerswap over I sanded the aluminium rims with an emory wheel chucked in my drill and slathered a bit of high temp Lithium grease on the rim/hub interfaceLee Lau - xxx-er is the laziest Asian canuck I know
-
04-25-2022, 06:49 PM #2
-
04-25-2022, 06:58 PM #3Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,043
they were stuck on there last fall and kicking didnt work, also tried using a big hammer & 2x4 against the back of the wheel from the other side of the truck which didnt work either
Lee Lau - xxx-er is the laziest Asian canuck I know
-
04-25-2022, 07:16 PM #4
Kick harder, like you're a horse. 2nd the antiseize, don't be stingy with it, it will help a lot.
-
04-25-2022, 08:13 PM #5one of those sickos
- Join Date
- Oct 2005
- Location
- Tahoe-ish
- Posts
- 3,151
I had to wail on my RV rims with a 16# sledge to get them unstuck from the hubs once. Grease is your friend upon reassembly.
ride bikes, climb, ski, travel, cook, work to fund former, repeat.
-
04-25-2022, 08:22 PM #6
I've had the same issue with my wife's Toyota Matrix. I hit those things so hard with a 10 lb sledge that I was worried about damaging them. The solution was to loosen all the lugs on the stubborn wheel a turn and then I went and did donuts in the parking lot until it popped free. After that I antiseized the rotor wheel interface. One time that wasn't enough and I used a 8" clutch puller and that was the ticket. Since then I've made sure to have antiseize against the rotor AND the part of the hub that contacts the wheel too.
-
04-25-2022, 08:25 PM #7Registered User
- Join Date
- Oct 2010
- Posts
- 1,958
Yup, had this on my jeep that I neglected to do rotations on for like three years in the salt belt.
First spray it down with some sort of corrosion-breaker. PB blaster is my go to.
Then:
#1 kick the tire while it’s jacked up
#2 sledge on tire (not rim) while it’s jacked up
#3 if these failed, put the lug nuts back on but a little loose, lower the car so the weight is on the wheel again and see if it pops off. If not, wail on it a little, if still not, drive slowly back and forward in the driveway, checking it every time you stop (you don’t want to drive too much with the wheel loose or you’ll put too much stress on the lugs)
-
04-25-2022, 08:35 PM #8Registered User
- Join Date
- Aug 2013
- Location
- shadow of HS butte
- Posts
- 6,430
Just dealt with this on my 4Runner last fall when I was removing the aluminum wheeled summer tires.
Mini sledge did not work.
Kicking did not work.
Dropping it down with the lugs loosened and rocking the vehicle did not work.
Ended up jacking it back up and going to bat with a 4’ long 4x6. That puppy worked almost instantly. Anti seize was applied afterwards.
Sent from my iPhone using TGR Forums
-
04-25-2022, 08:38 PM #9
Heh, I had this happen on my F250 once. After that, I decided paying someone $20 to rotate tires on an 8 lug truck was well worth it.
-
04-25-2022, 09:41 PM #10Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,043
yeah so I can just pay the shop but what happens in the middle of fuckin nowhere if that shop isnt there to get the wheel off ?
I really wana thank ever one for posting all the shit that doesnt workLee Lau - xxx-er is the laziest Asian canuck I know
-
04-25-2022, 10:49 PM #11
-
04-26-2022, 12:52 AM #12Registered User
- Join Date
- Jan 2011
- Location
- Calgary, Alberta
- Posts
- 362
I've had good luck wailing on the seized wheel with another wheel. Use the spare if it's full size. Had a seized wheel on a rabbit years ago - kicking it didn't work sledge didn't work, huge pry bar didn't work (literally lifted the vehicle), but < 10 whacks with a wheel going back and forth got it loose. All the other shit I tried probably loosened it, but the wheel was what got it off.
-
04-26-2022, 05:33 AM #13
-
04-26-2022, 06:00 AM #14Registered User
- Join Date
- Oct 2010
- Posts
- 1,747
And when you replace the rotors make sure the middle part is coated.
-
04-26-2022, 08:00 AM #15
Get steel wheels
Sent from my iPhone using TGR Forums
-
04-26-2022, 08:43 AM #16
-
04-26-2022, 09:23 AM #17
Been there more than a couple of times. Sometimes a few kicks work. Sometimes my Big Fucking Hammer works. What has always worked on stuck wheels is loosening the lug nuts a turn or two and driving at a slow speed while I "Rock the Boat" with the steering wheel. Then put the anti seize on so you can change a flat in the boonies.
Seeker of Truth. Dispenser of Wisdom. Protector of the Weak. Avenger of Evil.
-
04-26-2022, 09:36 AM #18
Loosen the lugs, and drive (bump) the wheel into a curb.
Plenty of Anti-seize on reassemble.
-
04-26-2022, 11:37 AM #19Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,043
Obviously brute force if they are stuck but I don't want them to stick so what to use, either anti sieze or grease or whatever
I went with a good cleaning & the white lithium grease cuz it doesnt melt or break down so it shouldnt migrate to brake surfacesLee Lau - xxx-er is the laziest Asian canuck I know
-
04-26-2022, 11:42 AM #20Registered User
- Join Date
- Aug 2013
- Location
- shadow of HS butte
- Posts
- 6,430
-
04-26-2022, 11:46 AM #21
Wear some real work boots, stop skipping leg day, and kick that fuckin tire, you pansies.
-
04-26-2022, 12:06 PM #22Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,043
existing the neanderthal methods didnt work but how would they know this until they learn to read
The rims arent stuck right now, i want to put something on the rims so they don't stick, my choices would appear to be grease or anti-sieze
i've heard one shouldn't put anti sieze on wheel nutsLee Lau - xxx-er is the laziest Asian canuck I know
-
04-26-2022, 12:12 PM #23
Antiseize on the rotor wheel interface and hub rotor if they contact. No antiseize on studs. Put some on but not a ton. I typically re-up when I swap tires and every couple years hit the accumulation with a wire wheel and start over. It has been working quite well.
-
04-26-2022, 05:25 PM #24Registered User
- Join Date
- Jan 2011
- Location
- Calgary, Alberta
- Posts
- 362
-
04-26-2022, 05:35 PM #25Registered User
- Join Date
- Nov 2007
- Location
- So. VT
- Posts
- 2,829
Tried all manner of kicking before, then tried the loosened lug nuts and a donut.
Once off the rust gets knocked off and a swipe with anti seize. A dab on the threads too. Next time it all comes apart
Before the bitching about sliver goop everywhere just a dab
Before the bitching about torque values I reduce based on wet torque values.
Bookmarks