WTB bomber bindings 115

[cantspin]

Grabbed a pair of animas w older griffons for a sweet deal of SOVT Joe. The bindings are hella shaky so I’m gunna need a replacement.

What are some bomber older bindings? Looking for something solid, heavy and cheap. Sick of this plasticy marker bs


Sent from my iPhone using TGR Forums

[cantspin]

pic of the skis looking sexy for motivation


Sent from my iPhone using TGR Forums

[Pukesno]

PX18

[1000-oaks]

solid, heavy and cheap

Yep, hard to get heavier, burlier, and cheaper than PX14 Racing, PX15, or PX18.

[skis_the_trees]

If you're planning to use them with a touring type sole (not standard alpine DIN sole) then that will factor into your binding choice -- none of the old PX series will work.

[pfluffenmeister]

Kiwi green P14s with 115mm brake.
$175+ship?

[TWODIEFOUR]

With a little duct tape for good measure.

[pfluffenmeister]

With a little duct tape for good measure.

Those look more like killer bindings than bomber bindings.

[cantspin]

Kiwi green P14s with 115mm brake.
$175+ship?

Too much $ but thanks


Sent from my iPhone using TGR Forums

[cantspin]

If you're planning to use them with a touring type sole (not standard alpine DIN sole) then that will factor into your binding choice -- none of the old PX series will work.

I’m in dynafit beast carbons rn I’ll make sure to research the compatibility


Sent from my iPhone using TGR Forums

[TWODIEFOUR]

Yep, hard to get heavier, burlier, and cheaper than PX14 Racing, PX15, or PX18.

if you have human feet (not bear feet), this is the correct information - either the Look PX-Series or Pivot series.

You should easily find a pair for the...bear minimum.

[waxloaf]

I’m in dynafit beast carbons rn I’ll make sure to research the compatibility


Sent from my iPhone using TGR Forums

Yeah I seriously doubt that those will work with old PX binders (or any old, heavy, burly clamps that I can think of). I’ve got some wardens I could sell you that would work, pm me if you’re interested.


Sent from my iPhone using Tapatalk

[HAB]

Yeah I seriously doubt that those will work with old PX binders (or any old, heavy, burly clamps that I can think of). I’ve got some wardens I could sell you that would work, pm me if you’re interested.


Sent from my iPhone using Tapatalk

Yeah, wanting them to work with those Dynafit boots is pretty limiting. waxloaf's Wardens are a good option. Otherwise you're basically looking at AAAttacks with the AT designation (NOT the regular or GW ones) or a Marker ID binding.

[1000-oaks]

Didn't notice the boots, yes Jester 16 ID or Attack2 AT are your best option.

[cantspin]

Well fuq didn’t realize these boots would be so limiting. Is it just because they’ve got less duck bill on the toe?


Sent from my iPhone using TGR Forums

[cantspin]

Anybody have some jester Toes? The heals are mounted fine the toes aren’t so fine


Sent from my iPhone using TGR Forums

[californiagrown]

Im a big fan of STH16s, or STH2 16s. Im an idiot and have trouble stepping into pivot heels quickly and easily... plus setting up pivots when you mount them is a little finicky. AAAttacks are also a good choice- i like the feel of those tyrolia bindings.

[HAB]

Im a big fan of STH16s, or STH2 16s. Im an idiot and have trouble stepping into pivot heels quickly and easily... plus setting up pivots when you mount them is a little finicky. AAAttacks are also a good choice- i like the feel of those tyrolia bindings.

Good bindings, but not compatible with his boots.

[waxman]

Well fuq didn’t realize these boots would be so limiting. Is it just because they’ve got less duck bill on the toe?


Sent from my iPhone using TGR Forums

well that and the vibram sole and the sole dimensions aren't alpine DIN standard

[MakersTeleMark]

[D-Roc]

It's the rocker of the boot that causes the interference

[1000-oaks]

If you want to run burly alpine bindings, get alpine boots and be done with it.