Results 26 to 50 of 80
Thread: Ripmo AF
-
06-23-2020, 09:40 AM #26
-
06-23-2020, 10:16 AM #27Registered User
- Join Date
- Dec 2009
- Location
- Sun Valley, ID
- Posts
- 2,547
Yeah. I’m kind of on the fence between Ripley and RipMo. Really very very similar bikes. You really don’t lose much going to the RipMo. Pedals very similar and only about 1lb difference.
Not sure how that plays out following vs offering. And the new following is brand new. Guess a new offering is in the works.
-
06-23-2020, 11:09 AM #28
I think they did the Offering update first.
Just like the Ripmo/Ripley, the Offering/Following seems to be, "Why not" The Ripmo gives all the acceleration of the Ripley with more DH chops. Seems to be the same with the Offering/Following.
Both bikes seem to make their smaller brothers sort of, "Why bother?"
-
06-23-2020, 12:47 PM #29Registered User
- Join Date
- Dec 2009
- Location
- Sun Valley, ID
- Posts
- 2,547
-
06-23-2020, 08:37 PM #30
I know that jenson just got a shipment of ripmos, so bikes earmarked for sept are shipping now.
-
06-23-2020, 10:11 PM #31Registered User
- Join Date
- Dec 2009
- Location
- Sun Valley, ID
- Posts
- 2,547
-
07-05-2020, 04:00 PM #32Registered User
- Join Date
- Nov 2003
- Location
- none
- Posts
- 8,368
I replaced my GX HD3 with the SLX Ripmo AF today.
Pat at Aspen Bikes has 9 with varied builds.
-
09-13-2020, 05:59 PM #33
Bump, as I'm daydreaming... Considering (but only half seriously) a Ripmo AF Deore build at $3200, and swap all the Deore bits for a mix of SLX/XT via eBay.
Stock Ibis hubs OK?
$100 to swap for coil rear shock is interesting... As is $800 up charge for Ibis carbon rims, with same house hubs.
-
09-13-2020, 06:01 PM #34
I have the ibis 742 wheel set and it has been so bomber. It does have a dt350 rear hub. I think I paid around $650 when they were on close out.
-
09-13-2020, 06:08 PM #35Registered User
- Join Date
- Mar 2005
- Location
- Livingston, MT
- Posts
- 1,793
Stock ibis hubs on their alu rims. Been beating them all spring and summer, bearings still spinning nicely and no slop. Few dents in the rims, but holding tubeless with no issues, so no worries there.
I’d roll with the Deore until it’s dead, what’s the issue besides it’s a little heavier than slx/xt?
Sent from my iPhone using TGR Forums
-
09-13-2020, 06:30 PM #36
I like the crispness of the higher Shimano shifters - usually go with XT for a shifter, SLX brakes, rear derailleur, and cranks - unless a deal shows up on XT for any of that. I haven't ridden any of the Shimano 12-speed though, so all this is based on earlier Shimano experience.
The additional $800 Ibis wants to go from Deore to SLX doesn't look worthwhile, as all the SLX bits could be purchased for less.
-
09-13-2020, 09:51 PM #37
Ibis used to rebrand Novatec hubs on their lower end wheels. I don’t usually break stuff but went through 2 of those POS hubs.
-
09-14-2020, 12:21 AM #38
The SLX package does come with Bikeyoke Revive over the low end KS post the Deore package comes with. That's probably worth $200-250 right there and is an upgrade I'd want to do regardless.
I've been looking at the Ripmo AF for a while as a possible replacement for my old Delirium. Not sure I'd ride it enough to get my money's worth out of it. It would have to pedal well enough I wouldn't hate climbing on it.
I've got Ibis hubs on my Mojo3. They're ok. But like the Stans hubs the pawls on the hub aren't very strong and can fail. More likely to happen if you ride somewhere like Moab/GJ a lot where you're powering up short steep sections. I can't imagine wanting to do that on a Ripmo so maybe they'd be fine.
-
09-14-2020, 07:49 AM #39
-
09-14-2020, 08:39 AM #40
-
09-14-2020, 09:20 AM #41
What’s the right rear shock buy with this frame?
The topaz
The jade coil for $100 more - (does this have a cheater switch?)
The X2 for $300 more
Sent from my iPhone using TapatalkBest Skier on the Mountain
Self-Certified
1992 - 2012
Squaw Valley, USA
-
09-14-2020, 09:35 AM #42Registered User
- Join Date
- May 2018
- Location
- NorCal
- Posts
- 835
I love the topaz on mine, but I would really like to at least try the Jade. The topaz could use a little more small bump sensitivity. The DVO stuff is amazing in my experience so far. Incredible plush, easily tunable, and very easy to work on at home.
-
09-14-2020, 10:05 AM #43
The bike yoke posts are really nice.
Ibis wheels are fine. The S stands for Stans rims, and they redesigned the hubs a few years ago. Not sure if they're still manufactured by JoyTech/Novatec, but they're 4-pawl, leaf springs, with the same bearings as everyone else.
-
09-14-2020, 02:05 PM #44
-
09-15-2020, 06:49 AM #45Registered User
- Join Date
- Nov 2003
- Location
- none
- Posts
- 8,368
My Slx came with the Jade coil and Spank wheels.
It’s a little heavy, but nothing’s broke in two months of riding park.
-
09-15-2020, 01:33 PM #46Registered User
- Join Date
- Oct 2005
- Posts
- 88
I got the NX build back in the spring. It's been great and held up well to some hard riding in WA and CA. It's damn heavy but the pedaling position is comfy so not a big concern for me. The ibis wheels have been solid, one minor ding in the rim from a big square edge hit but it keeps rolling straight. The Topaz has felt good. I miss the knobs and tuning of my previous cane creek. Haven't messed with volume spacers. The Diamond fork, which may not be on the current builds, has been just okay. It's taken a lot of tuning to get it to feel right and I'm running it way different than recommenced based on my weight. Also my build came with the bikeyoke post for some reason and I can confirm that it is awesome.
-
09-15-2020, 01:46 PM #47
The ibis hubs on their first round of wheels 6 or 7 years ago were pretty bad. I went through a few. The newer versions (eventual warranty replacements for v1) have been flawless. 190lbs and tend towards lower cadences vs spin to win.
-
09-15-2020, 01:58 PM #48
What kind of weights are you getting for an average build?
-
09-15-2020, 02:44 PM #49Registered User
- Join Date
- Feb 2014
- Location
- NorCal coast
- Posts
- 1,970
-
09-15-2020, 04:24 PM #50Registered User
- Join Date
- Oct 2005
- Posts
- 88
Yea about 35lbs. But considering the value and performance I'm fine with it. The only time I think about it is when I lift it on the rack. Forgot to mention the 175 cranks, too long for the low bb. Lots of pedal strikes in rocky pedaly sections.
Bookmarks