Results 1 to 17 of 17
Thread: Binding mount w/o boots?
-
02-06-2020, 07:29 AM #1Registered User
- Join Date
- Mar 2008
- Posts
- 142
Binding mount w/o boots?
I f’ed myself real good. I was recently in japan where I keep a pair of praxis protest as my only ski. After subpar winter they’re having (besides this last epic week) I came home wanting something else to play on. Scored a sick deal from Ptex1 and got after it. Now I mount my own bindings at my house in Portland, where my tools are. Bindings are enroute from pdx. Skis shipped from Ptex1. Ordered a new drill bit. Got myself prepared to mount without my jig with paper templates. I just realized my ski boots are in Japan. Fucken dumbass move. I live in Hawaii... where everything is being shipped.... So any way to mount some look pivots with paper template without ski boots in hand?
Tl;dr: can you mount ski bindings w/o ski boots?
Hoping someone can help me mcgyver this.
Mahalos
-
02-06-2020, 07:51 AM #2
i wouldn't fret too much over it, the reason a shop wants a boot is to set up the jig which you don't have/need
set the paper template to your bsl (hopefully you know it), drill skis and mount the bindings. set fwd pressure when you have your boots at a later date, done
if its a major concern just borrow a boot locally with same bsl, even better if you can source the same boot
pivots have a pretty wide range of adjustment for fwd pressure so getting it close should work fine
-
02-06-2020, 07:51 AM #3
-
02-06-2020, 07:53 AM #4
You use BSL to mount with paper templates. So if you know your BSL you’re set. If not you should be able to find out through the boot manufacturer based on the model and size.
-
02-06-2020, 08:04 AM #5Registered User
- Join Date
- Mar 2008
- Posts
- 142
Thanks for the feedback! That’s definitely a relief. I’ve never used paper templates before. I know the Bsl so I should be fine. TGR always droppin the knowledge.
-
02-06-2020, 08:23 AM #6
-
02-06-2020, 09:01 AM #7Registered User
- Join Date
- Mar 2008
- Posts
- 142
-
02-06-2020, 09:23 AM #8
Find a centerline.
-
02-06-2020, 09:27 AM #9Registered User
- Join Date
- Mar 2016
- Posts
- 354
To verify the template once you've gotten it taped up, the distance from the rear holes of the toepiece to the front holes of the heel piece on center should be your BSL (in mm) minus 97 or 98. I've mounted pivots like that with no template and they are right on. Vitamin I is who posted that formula originally.
-
02-06-2020, 09:34 AM #10
-
02-06-2020, 01:53 PM #11
Exactly. The new templates are sweet.
Fold in half at your bsl size. Tape to ski at boot center Mark
Center punch the holes and drill. A large framing nail makes a great center punch
I find it easier to do toe and heel separately rather than taping them together.
Put masking tape down the middle and draw a nice centerline first. Then mark your ski boot center.. . .
-
02-06-2020, 04:05 PM #12
-
02-06-2020, 05:46 PM #13Registered User
- Join Date
- Mar 2008
- Posts
- 142
-
02-06-2020, 06:18 PM #14
-
02-06-2020, 06:33 PM #15Registered User
- Join Date
- Mar 2008
- Posts
- 142
-
02-06-2020, 10:03 PM #16
Sounds like op has freehanded binding mounts. That shit is always off by a few degrees at best
The interwebs templates are money. I think better than some jigs.
As has been said just double check the scale of the print with a ruler.
You got this. . .
-
02-06-2020, 10:59 PM #17Registered User
- Join Date
- Mar 2008
- Posts
- 142
Bookmarks