Results 51 to 75 of 96
Thread: opinions on bd helios bindings
-
12-22-2019, 10:59 AM #51one of those sickos
- Join Date
- Oct 2005
- Location
- Tahoe-ish
- Posts
- 3,147
I think the ATK R12 2.0 that is on my VTA88 is what started Gimpy on this quest, and the above photos are super helpful as a resource, so here are some of the R12. It is a beautiful piece of engineering, and the brake works so smoothly that I have left it on (haven't skied with brakes in 10 years). I can't speak to the hard snow performance since I don't ski at resorts, but they are my favorite of any binding I've used for touring. (This group includes original TLT, Comforts, Vertical, Radical, Ion, MTN, and ATK skimo bindings.) The MTN/Backland is 2nd place.
WRT the riser heights, the photos will tell the story. 5 is 2 more than I need, but it's not a problem. I require a flat mode, and can't understand why a mid-weight binding would not have one. (I'm looking at you, Helio 180.) The riser over pin mode is nice when the skin track is consistently up from the transition point, and saves having to spin the heel. The magnetic flippy risers are a nice touch.
All of that said, I'd probably buy the Helio 200 or ATK equivalent instead. The R12 features are super nice, but personally I'd rather save the weight. The deal I got for this setup was crazy though. Also, FYI, the R12 heel screw pattern appears to be unique. (If it weren't I'd trade these for the H200 that Gimpy will prob get.)
Sent from my SAMSUNG-SM-T707A using TGR Forums mobile appride bikes, climb, ski, travel, cook, work to fund former, repeat.
-
12-29-2019, 08:08 AM #52
Does anybody know if it would work to run the Helio 200/Haute Route without the heel adjustment plate? I'm a weenie who's overly sensitive to binding ramp, and I'd be interested in trying that. Obviously you'd be committed to a certain BSL and lose some riser height, as well as having a smaller mount pattern in the ski, but I think I can live with all of that.
-
12-29-2019, 10:28 AM #53
Shouldn't be an issue, as the Helio 145 can be mounted to the Helio heel plate. Both H200 and H145 have the same four hole base.
-
12-29-2019, 10:30 AM #54one of those sickos
- Join Date
- Oct 2005
- Location
- Tahoe-ish
- Posts
- 3,147
Sure. It's just the separate solid plate style of heel adjuster, so you could mount the heel piece directly to the ski instead.
However, add someone who has a set of race bindings on some skis, I'd recommend using the plate. Having the ability to change BSL is very nice, even just for resale. You can even out the ramp with a plastic shim under the toe instead. If you're really that concerned about weight you'll get a U spring race binding anyway.
Sent from my SAMSUNG-SM-T707A using TGR Forums mobile appride bikes, climb, ski, travel, cook, work to fund former, repeat.
-
12-29-2019, 11:02 AM #55
And ... the ramp angle with the plate is still quite low. Not flat (which you might be after) but low.
... ThomGalibier Designcrafting technology in service of music
-
12-30-2019, 01:05 PM #56
Thanks guys. Toe shims are obviously a good option too – already running them on a bunch of my skis. The idea here would be to go as weight weenie as I can while staying away from a U spring heel, and getting a nearly flat binding, but those few grams probably aren't worth it. Just food for thought.
-
12-30-2019, 01:12 PM #57Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,002
I don't think they are up here yet and the pro i know doesn't have any info on if/when they will be coming and he would
Lee Lau - xxx-er is the laziest Asian canuck I know
-
01-02-2020, 10:37 PM #58
Any suggestions for mounting these beauties on a ski that has a metal sollyfit plate? I have to think even epoxy will just crack at some point (plastic glued to metal) yeah? There's a Loctite "plastic bonder" ...
Did you mount the ones paired with speed rads right into the ski?
Me = “knowledge worker” so be gentle if this is obvious .
-
01-02-2020, 10:53 PM #59
Drill and tap hole in the Sollyfit plate and bolt it to that?
-
01-02-2020, 11:49 PM #60
-
01-03-2020, 12:06 AM #61
-
01-03-2020, 08:53 AM #62
-
01-04-2020, 07:39 AM #63Registered User
- Join Date
- Jul 2005
- Posts
- 3,230
opinions on bd helios bindings
As a fellow “knowledge worker” (read over consumer of porn) I’d suggest you either fully remove the plate and remount the heels if you really want that spacer - as long as it wouldn’t leave your heel resting on your boot (there’s still a gap).
Sent from my iPhone using Tapatalk
-
01-13-2020, 05:13 PM #64Registered User
- Join Date
- Nov 2011
- Posts
- 84
Just picked up some trofeo pluses (helios 180s). Getting ready to mount them i noticed that the heal track/baseplate are shown in opposite directions on the BD site and and the ATK one.
It looks like the binding is designed with a slightly offset detent for the sideways position so if you mount it the atk way you get less heel binding in flat mode. And at least the outdoor gear lab review mounted it the BD way and complained about binding.
-
01-13-2020, 06:37 PM #65Gel-powered Tech bindings
- Join Date
- Dec 2004
- Location
- Amherst, Mass.
- Posts
- 4,684
Wow, good eye -- I never noticed that!
So playing around with a pair, yes, you're correct: mounted the way on the ATK website, the contours of the binding allow for more clearance of the boot heel in flat mode.
Whereas on the BD and Outdoor Gear Lab websites, the contours will jam into the boot heel more readily.
(Or you can also increase the gap a bit to more like 5mm -- given the decent length of the heel pins, and the generally robust design, you can probably get away with it if you aren't stomping monster jumps, etc.)
For the pics on the BD and Outdoor Gear Lab websites, the plate needs to rotated 180 degrees, and then the binding needs to be spun 180 degrees on its pedestal.
(Or for an already mounted setup, unbold the binding from the plate, rebolt the binding at 180 degrees to its original position, then spin the binding 180 degrees on its pedestal.)
And amusing as always to see the Outgear Gear Lab ratings for weight (which already has its own inherently quantified rating in the form of a standardized systems of weights and measures), downhill performance (where if anything it's more secure than any of the other relatively traditional heel pin bindings), ease of use (what is reflected in the missing three points?), and touring performance (6 out of 10, really?).Mo' skimo here: NE Rando Race Series
-
01-15-2020, 02:54 PM #66Gel-powered Tech bindings
- Join Date
- Dec 2004
- Location
- Amherst, Mass.
- Posts
- 4,684
Also just noticed that the Outdoor Gear Lab review claimed the binding has only one heel elevator position.
Granted, the higher position gets you only another half cm, but still, the binding is deliberately designed (and advertised as such) with two heel elevator positions (as opposed to other race-style bindings, where spinning the binding 180 degrees on its pedestal and flipping back the heel elevator all the way is explicitly discouraged), but still, would help the credibility of a product review to at least understand all the features of the product being reviewed (especially a product with so few features).Mo' skimo here: NE Rando Race Series
-
05-01-2020, 06:20 PM #67
Anyone have a pic of the BD Helio 180 mounted with a ATK Freeride Spacer?
-
05-01-2020, 06:31 PM #68
-
05-01-2020, 06:58 PM #69
Checkout ATKs website for the Trofeo Plus, they have some great templates and mounting instructions
-
05-01-2020, 07:36 PM #70
ATK's Haute Route template was really close. I found myself having to move some holes a half mm or so. A few test mounts are in order.
Also, you may not find every template on their site. Many of their bindings are mashups. For example, the RT 10 I mounted was very close to a Crest heel and the Haute Route toe (and likely other toes as well).
My memory is a bit fuzzy, and I may be mixing up the specifics, but you get the picture. Don't give up if you don't see what you need. Indeed - the Trofeo Plus is the Helio 180.
... ThomGalibier Designcrafting technology in service of music
-
05-02-2020, 04:22 AM #71Gel-powered Tech bindings
- Join Date
- Dec 2004
- Location
- Amherst, Mass.
- Posts
- 4,684
-
05-02-2020, 08:42 AM #72
What holds the climber flap in place on helio 180’s/trofeos?
Do they have a tiny magnet like the 200’s, or just a detent or friction fit?
Sent from my iPhone using TGR ForumsGravity always wins...
-
05-02-2020, 08:59 AM #73a positive attitude will not solve all of your problems, but it may annoy enough people to make it worth the effort
Formerly Rludes025
-
05-02-2020, 09:09 AM #74Gel-powered Tech bindings
- Join Date
- Dec 2004
- Location
- Amherst, Mass.
- Posts
- 4,684
-
05-02-2020, 09:22 AM #75
Even though the thread I linked says otherwise my digging showed no mention of the magnetic flaps.
a positive attitude will not solve all of your problems, but it may annoy enough people to make it worth the effort
Formerly Rludes025
Bookmarks