Results 26 to 50 of 327
Thread: Let’s see your home wax bench
-
09-11-2019, 01:38 PM #26
The only bench I know. Everything you need is there. You just have to dig for it.
Sent from my Pixel 2 using Tapatalk
-
09-11-2019, 09:29 PM #27Registered User
- Join Date
- Nov 2017
- Posts
- 38
Two 4x4 blocks, wrapped in rescue tape, work beautifully for those who don't want to shell out $100+ for vises
-
09-13-2019, 03:29 PM #28Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,040
Thats pretty much the whole setup, the ski holders and the universal jig that will mount everything
the slot in that T jig will hold a ski or board on edge, make 2 of them and zap em to the bench with drywall screws where ever needed
that bench is made from a cut up water bed frame that a downstairs tennant left, so because i got a tennant I got lotsa money but no basement
so this tuning bench is in the spare bedroom, a 4x8 sheet of OSB protects the laminate floor from wax or dropped toolsLast edited by XXX-er; 09-13-2019 at 04:17 PM.
Lee Lau - xxx-er is the laziest Asian canuck I know
-
09-13-2019, 05:26 PM #29
-
09-13-2019, 06:08 PM #30
-
09-13-2019, 06:55 PM #31
-
09-14-2019, 09:51 PM #32Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,040
so for all you folks with no where to put up a permanent work bench of your own here I used a black n decker workmate to hold the various jigs I made to hold the clamps. its all just 1x4 and drywall screws cheap n easy
I made the waxing jig with the cleat on the bottom to be held by the workmate,
the vise is also bolted to a wooden cleat
I used to bolt a cleat on the bottom of a park prs4 bench mount deluxe bench model repair stand also which worked great
you could/you should buy one of these bad boys and tell the wife you needed it for all them home improvements ehLee Lau - xxx-er is the laziest Asian canuck I know
-
09-15-2019, 11:38 AM #33
-
09-15-2019, 03:15 PM #34
-
09-15-2019, 05:04 PM #35
Still in flux after moving. Yearning for garage space.
-
09-15-2019, 06:31 PM #36
-
09-15-2019, 06:58 PM #37
Good stuff in here.
-
09-16-2019, 06:45 AM #38Registered User
- Join Date
- Jan 2015
- Posts
- 223
-
09-16-2019, 09:14 AM #39Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,040
Hmmmm, I have an 8 ft piece of 16" wide OSB sitting around that I use for regluing skins,
maybe I will make it into a wax box that can still be turned upside down for the very odd ski gluing job
cuz the wax shavings are a painLee Lau - xxx-er is the laziest Asian canuck I know
-
09-16-2019, 09:28 AM #40
Wax box looks great.
For most of my maintenance waxes, to mitigate scrapings I changed waxing method to crayoning a wafer thin layer of wax, iron it in and just buff it smooth. No scrape.Master of mediocrity.
-
09-16-2019, 09:36 AM #41
-
09-16-2019, 09:45 AM #42
My old man had a non-ski workbench that looked like this, he knew where everything was unless one of us kids used it and put it someplace else in the pile, then he was SOL.
Sent from my iPad using TGR Forums
-
09-16-2019, 09:45 AM #43Registered User
- Join Date
- Nov 2015
- Posts
- 28
I watched a guy wax a pair of skis crayoning the wax on the base and using a heat gun, no iron, nothing on the bench, no clean up.
-
09-16-2019, 09:56 AM #44
-
09-16-2019, 10:39 AM #45
-
09-16-2019, 12:14 PM #46
Tried that too but it was actually more time consuming and took more mental focusing energy than the crayon/iron method.
Sometimes buff with palm of leather ski gloves to give 'em a little boost of water repellency and boost grip tackiness but usually just use a plain old scotchbrite pad. IME, almost anything does the job though; old sock, paper towel, etc....
Master of mediocrity.
-
09-16-2019, 01:30 PM #47Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,040
I hung out top side at the Canadian 4 cross championships as the go for when they were here
the wax guys had already waxed all the skis the night before, before each race they would rub a little piece of high fluro into the ski, rube it in with a a cork and take it all off with a roto brushLee Lau - xxx-er is the laziest Asian canuck I know
-
09-16-2019, 05:18 PM #48Registered User
- Join Date
- Jan 2015
- Posts
- 223
That’s a ski from the home ski museum (I dig Graves!) and is 190. I built the box for my longest ski in regular use, 188, but one could make any size wanted. I’ve also seen designs that are hinged in the middle so that they can be folded up, with supplies inside, and taken traveling.
-
09-16-2019, 09:02 PM #49
-
09-16-2019, 10:04 PM #50
Made a box like this for my future father in law who was all about Nordic racing. He could take it with him, stocked it up w tools and waxes etc.
Sealed the deal for this gal.
Sent from my iPhone using TGR ForumsI rip the groomed on tele gear
Bookmarks