Results 1 to 25 of 28
Thread: Enve M60 Forty HV 29" Rims
-
05-31-2019, 10:09 AM #1Registered User
- Join Date
- Aug 2007
- Location
- United States of Aburdistan
- Posts
- 7,281
Enve M60 Forty HV 29" Rims
These carbon rims only have a few rides on them, No dents and nothing more than some surface scratches on them. One can be registered for warranty with Enve. Comes with unknown aero spokes that came with the Enve rims, and enve nipples, rim tape.
I'm struggling with a fair price for these. I have them listed locally (UT) for $600, will do $500 for mag? I think that's fair. Shipping to lower 48 for cost of shipping from SLC.
-
05-31-2019, 11:46 AM #2
-
06-02-2019, 04:18 PM #3
What hubs? Boost? Driver type? Been looking for an XC-ish set for some slicker totes for the hardtail.
-
06-02-2019, 04:41 PM #4
-
06-02-2019, 05:05 PM #5
Ha! After I posted that I considered they were probably rims only, then I just went on living my life.
-
06-07-2019, 09:49 AM #6Registered User
- Join Date
- Aug 2007
- Location
- United States of Aburdistan
- Posts
- 7,281
Whoops, sorry I missed these comments. Yes, get what ever hub you want, get them built and have a bad-ass new set of rims for cheaper than some equivalent used ones. Or is my math off?
Again, one of these can be warrantied. That means use it as a back rim, to me. I think they offer a discount to ones that aren't registered/bought used but check the enve site to be sure.
These are in near perfect shape. And the spokes def look like bladed Sapim CX-Rays. but there's no logo or anything to identify them.
-
06-14-2019, 11:16 AM #7Registered User
- Join Date
- Aug 2007
- Location
- United States of Aburdistan
- Posts
- 7,281
Not sure why I can't sell these, make me an offer....
-
06-14-2019, 11:44 AM #8yelgatgab
- Join Date
- Oct 2002
- Location
- Shadynasty's Jazz Club
- Posts
- 10,249
-
08-07-2019, 12:52 PM #9Registered User
- Join Date
- Aug 2007
- Location
- United States of Aburdistan
- Posts
- 7,281
-
08-07-2019, 01:24 PM #10
It's not that I don't want them...
Anyway, isn't spoke length an issue as to whether or not you can use the included spokes?
Are the nipples/spokes used? Is that an issue?
A bike tech once mentioned to me that you can't reuse rims since once they've been laced up, there is a notch in the hole and therefore it won't fit being laced to a different hub with presumably different dimensions. Bullshit? Depends on the rim?
-
08-07-2019, 01:30 PM #11
-
08-07-2019, 01:33 PM #12
-
08-08-2019, 05:18 PM #13
Am I wrong in thinking this is a screaming fucking deal?
-
08-08-2019, 05:52 PM #14
I want these for my hardtail, but I have no more moneys to give.
-
03-02-2020, 04:54 PM #15Registered User
- Join Date
- Aug 2007
- Location
- United States of Aburdistan
- Posts
- 7,281
-
03-02-2020, 04:59 PM #16
Are these 26 mm inner width? I’m building up a wheel set for the GF, looking for 30 mm rims.
-
03-02-2020, 05:05 PM #17Registered User
- Join Date
- Aug 2007
- Location
- United States of Aburdistan
- Posts
- 7,281
Yes, specs are here:
https://www.enve.com/en/installation...chives/m60-hv/
-
03-05-2020, 10:40 AM #18
-
03-05-2020, 12:07 PM #19
Possible interest. What is the spoke length?
-
03-05-2020, 01:05 PM #20Registered User
- Join Date
- Aug 2007
- Location
- United States of Aburdistan
- Posts
- 7,281
-
03-05-2020, 07:47 PM #21
-
03-09-2020, 01:19 PM #22Registered User
- Join Date
- Aug 2007
- Location
- United States of Aburdistan
- Posts
- 7,281
OK, they are 292 end-to-end, but I learned that I shoulda measured from end-to-mid-curve if that makes sense. So 292is 1-2mm off is my guess. If you want a more exact measurement I can tonight.
-
03-09-2020, 08:22 PM #23
Yea, hook the J-bend over the end of your ruler. The threaded end will give you the length.
They might all be one length, or there could be 42 of one length and 14 of another length. Or three different or 4 different lengths. It's annoying, but you kinda gotta measure each one to not miss 2mm differences.
Really, to utilize the spokes, you'd either need to match the hub they came off, or just sell them on ebay.
Still, that's a Siiiiiiiiiiccckkkkk deal for 2 Enve rims even without the spokes. I'm sure they're a lot more burly than Chinese Ebay hoops.However many are in a shit ton.
-
03-10-2020, 11:12 AM #24Registered User
- Join Date
- Aug 2007
- Location
- United States of Aburdistan
- Posts
- 7,281
Thanks JM2e.
These are the hubs they came off of: https://wheelbuilder.com/dt-swiss-24...ake-front-hub/
-
03-10-2020, 09:15 PM #25
Well fuck me sideways.
Chances are the flange size/spacing is the same as 6-Bolt 240s as well as with 350s. If so, much bigger potential to match up those spokes.
Sent from my iPhone using TGR ForumsHowever many are in a shit ton.
Bookmarks