Results 26 to 50 of 95
-
02-18-2018, 08:34 AM #26
Personally, I think it's a 'must have tool' for any DIYer for base flattening, structuring, base repairs and even wax removal. Especially over time.
It can be labor intensive or super quick and convenient depending on the task. Structuring and base repair material removal can take seconds to minutes. Major base planing can take time and effort. You have the choice to decide whether it's worth the effort or not for the given task. You can micro manage how much removal ('grinding') you want to perform so as to not remove all your waxing efforts to 'freshen' the base. You can quickly open more aggressive structure for wetter snows or reduce for finer, colder snows.
Sometimes the goal of getting your bases dead flat is not your smartest or best option. For edge high, possibly a 1 or 2cm of flat base along the edge is all that is needed. More only takes away more material and does not necessarily improve performance. Same for base high. Also, the softer the snow the less it matters. You can flatten in stages and see how the skis change or not.
In the time I typed this, I could have restructured my bases or clean up a few base repairs.......Best regards, Terry
(Direct Contact is best vs PMs)
SlideWright.com
Ski, Snowboard & Tools, Wax and Wares
Repair, Waxing, Tuning, Mounting Tips & more
Add TGR handle to notes & paste 5% TGR Discount code during checkout: 1121TGR
-
02-18-2018, 12:27 PM #27
It's certainly possible to flatten the bases in stages but it's pretty time consuming to do it that way because base flattening requires multiple hot waxings following removal of base material. The bases will really absorb a lot of wax after the pore structure is opened up. I prefer to do it in one go.
Most people will want bases almost flat (very slightly base high is better than edge high). The best way to achieve that is to scrape the bases until they are flat (or very close to it) and then add your preferred edge bevel. Use the minimum iron temperature needed to get the wax to flow because too hot of an iron will close the base structure again and your skis will be slow and not hold wax well.
-
02-18-2018, 12:36 PM #28
Most skis I've done were a little base high but not evenly so across the skis or from tip to tail. Just draw the Ski Visions tool down the length of the ski and pay attention to where the most shavings are coming from. After a few passes it will start to even out. The key is to watch what the tool is telling you and to focus your efforts on the areas that need the most removal. Getting it close is usually good enough. Better to stop a little early. I've never found a pair of skis that were not significantly improved by a bit of base scraping, both in glide and in turning responsiveness and precision (consistency).
It takes a lot less time than the edge tuning and waxing.
-
09-02-2018, 09:18 AM #29Registered User
- Join Date
- Jan 2014
- Location
- Gaperville, CO
- Posts
- 5,852
Got one of these last week. Agree with most the comments here. Well worth the money -- the main costs must be in the stones. The planer isn't anything fancy but works fine.
Thus far I've done three pairs of skis
- One had a bunch of light scratches but were basically flat. 10 minutes of work had structure reapplied over the scratches, and then smoothed out.
- One pair had a number of large core shots that needed refinishing. And were pretty base high. Probably 20 minutes of work to get things relatively smooth and bases flattened. Felt sort of wonky working on this pair because of the microcambers (Deathwish) but overall look way better than prior.
- Last pair was a set of touring sticks. One of them was edge high underfoot. This definitely takes some time to bring the edges down with the tool, but it works. They don't look quite as good as fresh base grind, but its pretty close and I didn't have to pay a store or haul them down there.
Next ones I do I'll make sure to take before/after photos.
Pretty easy on skis up to 100mm. The bigger sticks take a little more care with even pressure and some side to side adjustment. Nonetheless, its pretty hard to fuck up skis with this.
Whether they actually ski better or not, who knows. I'm not a pro and mostly ski soft snow so it won't really matter. But it makes wax go on nice, they look prettier and it gives me a good excuse to spend more time working on skis instead of the house.
I could totally see owning the file-based tool for real planing work.
-
09-02-2018, 08:53 PM #30
-
09-03-2018, 10:09 AM #31Registered User
- Join Date
- Jan 2014
- Location
- Gaperville, CO
- Posts
- 5,852
-
12-18-2018, 10:52 AM #32Registered User
- Join Date
- Nov 2018
- Posts
- 39
Doebedoe, I recognize your username from the COsnow subreddit. Bit of background, I've never really liked my skis. They have always seemed a little twitchy. I have always just assumed I need to get the edges sharpened more often, but after a weekend of skiing on demo skis that I could steer on rails and getting back on to mine and constantly having my downhill leg slide out on me on icy patches, I thought there must be some other reason.
Did some research and learned about having "base high" bases and from everything I've read, it sounds like what I'm experiencing. So I'm on the hunt for a place to get the bases flattened (I know, I know I should learn to do it myself). I had these skis tuned at Crystal's in Boulder last year, so I'm somewhat hesitant to take them back there, but if I do, I'll definitely call this issue out specifically so they can correct. I just don't think they have a machine to do it (which I've read is better than trusting a potentially untrained tech to do it by hand...) Do you have any other recommendations? Given that these are now my beater skis, hoping to not spend a fortune. Doesn't have to be perfect, but would like to actually trust my edges on the hardpack.
Appreciate it!
-
12-18-2018, 10:58 AM #33Registered User
- Join Date
- Jan 2014
- Location
- Gaperville, CO
- Posts
- 5,852
-
12-18-2018, 05:31 PM #34Registered User
- Join Date
- Jun 2017
- Posts
- 93
Alpine Base and Edge in Boulder is the race tune shop. They're a funky looking shop but they have a high-end Wintersteiger base grinding machine and (more importantly) their owner and staff actually know how to use it properly. They won't take off too much material or put the wrong base pattern in your skis or put the wrong bevels on your skis.
If you specify the bevels you want they'll do what you specify, but I think their all-mountain default is 2 degrees on the edges and 1 degree on the base.
They are relatively expensive, and the owner Peter is very no-nonsense. If you tell Peter the symptoms you're experiencing he should be able to trouble-shoot your tune and recommend a fix.
-
12-18-2018, 07:36 PM #35
What's the cheap / easy / already in my garage way to check if my bases are all flat?
Sent from my iPhone using TGR Forums
-
12-18-2018, 07:59 PM #36
-
12-18-2018, 10:12 PM #37Registered User
- Join Date
- Nov 2016
- Posts
- 416
Opinions on the Ski Visions base flattener???
Get a metal ruler or other straight edge, test it for straightness against a window pane, then do what meadow skipper’s photo shows, checking for light under the straight edge.
Not to say a true bar isn’t worth it. It is.
Sent from my iPhone using TGR Forums
-
12-18-2018, 11:26 PM #38
Old thread with good recommendations from upallnight
https://www.tetongravity.com/forums/...69-Base-planer
Somewhere on the forum, he posted before and after photos of dumpster skis that he brought back to the living using the ski Visions tool.
-
12-19-2018, 10:07 AM #39Registered User
- Join Date
- Nov 2018
- Posts
- 39
Ya, I saw them come up in a Google search. Was hoping not to spend quite that much, since these skis will be the designated rock/ early season/ beat around skis. That being said, if the bases will stay flat for a while, maybe it's worth it. Any idea how or why mine ended up so out of whack?
-
12-19-2018, 10:38 AM #40
Think I'm gonna get one. Is there a "wide" version?
Sent from my iPhone using TGR Forums
-
12-19-2018, 10:39 AM #41
Why I like the base planer.
Less than 10min work time.Move upside and let the man go through...
-
12-19-2018, 10:48 AM #42
I have used one for a few years to flatten my bases. I do it once a year or more if skiing one ski a lot and I make the time. Perhaps because I do it infrequently I find it takes a good amount of patience to get the whole ski right. Finished product looks home done relative to a high end machine, but I am pretty happy with how the stone does and then knocking it down with the metal bar (don't need a true bar with the kit) and waxing and brushing.
If you have the time and like to work on your skis saves the cost of bringing them in.
I have done 114 waist skis with it. Would think tool is useless for base flattening on real wide skis or a snowboard.
I have not used it to bring down edges. East coast problems
-
12-19-2018, 11:02 AM #43Registered User
- Join Date
- Nov 2016
- Posts
- 416
-
12-20-2018, 06:01 PM #44Registered User
- Join Date
- Dec 2009
- Location
- Sun Valley, ID
- Posts
- 2,547
I’d really like to get hold of the file base flattener. But it sounds like it won’t be available any time in the near to mid future.
-
01-13-2020, 12:27 AM #45
Opinions on the Ski Visions base flattener???
Bump
I’ve been using my skivisions base flattened and structuring tool more and more lately. I’ve been following the vid instructions/methods from the skivisions guy, focusing on using the stone and minimal use of the blade. One of my wife’s skis her base high. It took a LONG time to get them pretty flat using the stone. In the future, should I have use the metal blade instead? Does it remove more material per pass compared to the stone? Also, the stone has some ski wax on it now, even though I used base cleaner (and a scraper) a few times on the skis. Is there a good way to get the wax off without fouling the stone? The wax is on the edge that I would not “lap,” per instructions....
Super stoked on the tool!
Cheers
-
01-13-2020, 04:40 AM #46Galibier Designcrafting technology in service of music
-
01-13-2020, 10:48 AM #47Registered User
- Join Date
- Dec 2009
- Location
- Sun Valley, ID
- Posts
- 2,547
Email I got back from Mark at skivisions when I emailed him for tips on making a base flat more quickly with his tool:
Crybaby. Go to the hardware store and get a 10" double cut mill bastard file. Now you have to use it EXACTLY as I say. Take the butt of your palm of hand and put it on top of the file. Tang in right hand if right-handed. Push the file down the ski two handed feeling that file cut. Like crazy. Metal and plastic. Do 1 edge at a time and check EVERYTHING after every pass down the ski. Rotate edge to edge one pass down each side. DON'T GET CARRIED AWAY! You are making magic not a mess. Just do it. Let me know. Oh, that file can make a mess. Clean it all up with my tools.
-
01-13-2020, 11:22 AM #48Registered User
- Join Date
- Nov 2018
- Posts
- 759
That is some badass customer service right there. I don’t need more tuning tools but this thread is giving me the itch...
-
01-13-2020, 11:34 AM #49
-
01-31-2020, 11:22 AM #50
I really like the flattener and wanted to get the file tool, however, Mark from Ski Visions doesn't seem very confident that the file tool will be available any time soon.
I went ahead and made my own version. I just routered a groove in a piece of hickory I had (very hard wood so it will remain flat) and epoxied a couple magnets in place to hold the file.
It works pretty well, especially dealing with edge-high issues. I run it over the entire base first and use the flattener tool after I'm sure the edges are level with the base. This should also save a lot of wear on the flat steel cutter.
Bookmarks