Results 51 to 75 of 230
Thread: Go Fast Campers, new mag product
-
10-25-2017, 11:52 AM #51
We have a rubber extrusion made that seals from the 1.5" round tube to the bed rails. The tubework lower rail has holes for through bolts that go into a machined adapter plate to either fit onto an existing track system (standard in a lot of newer trucks), or to a clamping setup for older vehicles like a traditional truck topper. No drilling into the bed required.
-
10-25-2017, 12:10 PM #52
Thanks man. We will have some operable hard side options soon, whether it's a window in the panel, or the entire panel is operable and swings up. It will be sealed to the tube when closed. The initial run will just be fixed sides or fabric however, but the lower framework will all be the same and you will have the ability to switch from fabric to operable panels to fabric etc.
Initial mattress size for the f-150 model is just under a full size width with enough length to sleep someone 6'6" easily with plenty of clearance above. It can fit someone like 7'6" tall, but the front section of the camper has a pretty low roof so it wouldn't be comfortable.
We are going to come out with an 'XL' version for fullsize trucks with a queen size mattress, and may offer that as an option with the f-150 in the future.
Thanks dude!
If we can get 5 first gen tundras with the same bed length, I can add that as a production run for this spring.
I think we will have most of that functionality as options on release.
We will absolutely make a version for that truck. I really hope they bring the ranger raptor in...
We will know more about options and our production plan as it happens, probably have a better understanding once we finish our production prototype in december. The options will interface with the existing lower structure, so you could totally pre-order the system now, and we can ship the system without sides (for less than the 5k of course, still need to finalize that pricing option) and get the sides to you once they are developed.
The pop up sides are not that heavy vinyl product FWC uses. We have experimented with tent sides (like, 5oz bivy tent material) and less breathable heavier options and have found both to work pretty well. The lightweight tent material was too loud, to fragile, and doesn't work great for waterproofing if its dirty. We are moving towards something in the middle, more along the lines of a sunbrella fabric.
That's wolfmobiles truck eh? It will have a small overhang, but there is a lot of "fixed" bed space because of how we configured our floor.
-
10-25-2017, 12:25 PM #53
No photos yet, just ordered the chromoly for the production prototype lower. It will be beadrolled (to stiffen) .062-.090 5052 sheet (good corrosion resistance and workability).
There will be a zip up headliner on the roof panel. The panel itself is translucent which creates a really nice ambient light in the space so you can wake up with the sun if you want to, and if there is any light outside you can still see inside the tent. The headliner will allow you to black it out. The panel is also thermally neutral, with a decent amount of insulation from the trapped air in the honeycomb. There shouldn't be much in the way of condensation from anything but breathing, and the headliner will keep that at bay.
Additionally we are working on ventilation systems to keep that to a minimum, both passive solar powered vents that are always flowing a small amount of air, to a larger system to cool the tent when occupied. We want to have it all integrate into the sides of the tent so we don't increase stack height. You could totally install a fantastic fan and a marine solar vent on the roof as it sits, but we plan to have some better alternatives.
We will likely be able to support your truck when we launch the XL version, hopefully summer/fall of 2018.
Yeah, we will be able to sell just the tent with the panelized floor system. It will probably be in the 3-3.5k range. We can also sell the spaceframe without any sides.
I think you'll be stoked on a lot of the options we are working on. We are staying narrow initially because we want to stay inside the existing body lines (vehicles taper from bed width to roofline) and offer a product that can support Tacoma/Colorado/Raptor off the bat.
We have been getting a lot of questions about that. We could totally make a taller lower assembly that would allow a moto to clear if there was a market for it. We just carry our bikes on hitch carriers currently, but that doesn't totally work for multiple bikes.
-
10-25-2017, 12:26 PM #54
-
10-29-2017, 12:02 PM #55
Bumping for the start of our production process series. Starting with a blog, but going to move towards vlogs as well this week. Basically outlining the design, reasons behind decision making, and real world testing to see if it works. Should be a bit slapstick, informative and hopefully worth watching.
First post ˇˇˇˇˇˇˇˇ
https://www.gofastcampers.com/gfc-blog/
-
10-29-2017, 07:05 PM #56
^^ very well done and informative.
"Zee damn fat skis are ruining zee piste !" -Oscar Schevlin
"Hike up your skirt and grow a dick you fucking crybaby" -what Bunion said to Harry at the top of The Headwaters
-
10-29-2017, 07:25 PM #57
A ton of great conversation, I'll have to come back and finish reading through. Looking forward to the version for a full-size pickup.
I definitely agree with the pass through. This system, integrated with a similar hardshell topper for a flatbed like the Ute canopy would be my ideal.
-
10-29-2017, 07:46 PM #58Registered User
- Join Date
- Oct 2007
- Posts
- 12,672
-
10-29-2017, 08:40 PM #59Registered User
- Join Date
- Feb 2014
- Posts
- 2,508
2000 s10 zr2?
-
10-29-2017, 08:46 PM #60Registered User
- Join Date
- Feb 2014
- Posts
- 2,508
-
10-30-2017, 06:47 AM #61
Stay tuned...
Apologies, bed size is the same so it will fit fine. I keep referencing the raptor because it is the reason we are supporting f-150 initially.
Not in the immediate production plan, but if we can get 5 people with the same generation truck and bed length we can offer products for that vehicle right off the bat. Otherwise we are hoping to be able to make a custom option where we can build to any vehicle for a fee.
-
10-30-2017, 08:29 AM #62Registered User
- Join Date
- Oct 2007
- Posts
- 12,672
If a guy can afford a Raptor you should be charging him $20K for a tent with upgraded sticker package.
Sent from my iPhone using Tapatalk
-
10-30-2017, 11:01 AM #63yelgatgab
- Join Date
- Oct 2002
- Location
- Shadynasty's Jazz Club
- Posts
- 10,249
Nice write-up. Thanks for the thorough responses.
Any idea of overall height on a '16 Tacoma? Ballpark?Remind me. We'll send him a red cap and a Speedo.
-
10-30-2017, 11:56 AM #64
Believe it or not, value per dollar (actual msrp, not paying over sticker like people have been) a raptor is actually good value. You can't build a "mid travel" ford for less money. A stripper crew cab is like 50k. An optioned out tacoma is like 40+ and way less capable in go fast applications. YMMV and all, but if you don't want to really modify the truck any further it is a great starting point.
No worries. So we are 7" above the shark fin if you have a third gen. 1" of clearance room above the fin, then our assembly is 6" thick. According to a google search, a stock taco is ~71", so that would put us at 6'6" overall height with stock tires/suspension.
-
11-01-2017, 09:16 AM #65yelgatgab
- Join Date
- Oct 2002
- Location
- Shadynasty's Jazz Club
- Posts
- 10,249
Thanks again. Gonna have to go measure the low point in the parking garage. I think it's 7'2", so I should be fine. I went ahead and reserved. You guys make it too easy being fully refundable. Plenty of time to figure out how to pay for it, and how to break it to the wife, though.
Remind me. We'll send him a red cap and a Speedo.
-
11-01-2017, 12:22 PM #66
Sweet, #19!
7'2" should be no problem. And yeah, we don't use the deposits in any way for development funding, thats all taken care of. We are literally just using the deposits to gauge interest and find out how much material we need to start ordering. Turns out the response has been really good so far
I'll drop you an email in the next day or so here to touch base, thanks for the support!
Also, to all the first gen tundra guys. I have been getting a lot of emails on those, if you are reading this and are seriously interested please let me know. I just need you to fill out the form on our FAQ page (very bottom) and it'll go into my spreadsheet of requests. We aren't too far off from offering it as an option.
-
11-05-2017, 04:20 PM #67
How much weight can it support when popped up?
We travel with two 17' FG sea kayaks + 2 SUP's and my old GMC Safari is on it's last legs, looking at trucks and vans right now. Hard to get the boats on top of a Sprinter etc.
-
11-05-2017, 09:13 PM #68
Assuming that the load is well distributed (on cross bars or a rack we are designing, 500# when being used as a roofrack, and 75-100 pounds on the rack if being opened for camping.
You could probably pop it with the SUPs, but the kayaks would likely be a no go. The other problem with the 17' kayaks, is that our design isnt great for long items like that, since its popping at an angle it would likely hit the cab of anything with a longer roof than a regular cab mini truck.
The best option in this case would be to pull the kayaks when popping up the camper.
Might be able to design something that would mount the kayaks to the lower extrusion, and be able to tilt off to the side of the vehicle when not in movement so you could still pop the tent, but that would take some doing. Have actually had a few folks that would really be interested in a design like that.
-
11-05-2017, 09:23 PM #69
Go Fast Campers, new mag product
Last edited by ticketchecker; 11-06-2017 at 06:29 AM.
-
11-06-2017, 04:16 PM #70Registered User
- Join Date
- Jan 2004
- Location
- North Vancouver
- Posts
- 6,459
This is rad. It's a concept that I am surprised we've not seen before. There are a few different takes on this style of pop up in Europe.
-
11-06-2017, 09:27 PM #71
They are happy in that 75-100 pound load range. We have provisions to adjust the strut geometry to help it lift a heavier load without changing to a heavier duty strut. Its not just the strut that is affected by the weight, it is also our strut over-rides that keep the roof up in case the struts fail.
Thanks man, there really isn't too much out there. I learned a lot from starting AeroContinental, and learned that simpler rigs appeal to just about everyone. People that have Earthroamers are just as likely to be interested as those who are scraping pennies to save up for a 5k setup. It just works, and you don't have to worry about it.
-
11-12-2017, 12:32 PM #72
Welded up a couple of Tacoma long bed lower frames yesterday. Unlike the square tube on the early test mule, these are 1.5" round mitered DOM tubing and made to the final design specs. We'll be skinning these in bead-rolled .090" aluminum this coming week.
Looks like we will have options for fixed and operable aluminum sides made of .080-.090 5052 Aluminum. Operable is where the two side panels are hinged to lift off the structure and create a cabana style space in the topper, or to access things from the side. We will also still be making fabric sides for select vehicles where we see a demand. Those end up being quite a bit lighter, and are really nice for desert travel.
Rear panel will be a glass hatch like a modern leer or ARE, and the front "bulkhead" panel will have an optional view window (likely non operable) to be able to see whats going on in the bed from the cab.
It's going to be a pretty burly structure...
-
11-15-2017, 09:35 AM #73Banned
- Join Date
- May 2007
- Location
- Sandy, Utah
- Posts
- 14,410
Thought this was neat.
http://www.outsideonline.com/2167796...n=facebookpost
Sent from my XT1650 using TGR Forums mobile app
-
11-15-2017, 09:42 AM #74
-
11-15-2017, 10:46 AM #75Banned
- Join Date
- May 2007
- Location
- Sandy, Utah
- Posts
- 14,410
Bookmarks