Results 3,701 to 3,725 of 5882
-
06-18-2022, 04:49 PM #3701Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
Sawzalls FTW.
I had a somewhat painless end (?) result today. I left the thing alone for a few hours to let everything go to sleep then pulled the neg cable and let it sit for 10 minutes then the POS cable and sit for another 10. Then I did the reset by holding the cables together and when they touched the parking lights flared for a second and the head unit threw a static burst. I about had a cow I held them together for about 30 seconds then reconnected.
The first startup is 2 lock to lock turns to calibrate the SAS and it threw a lost communication code so I turned it off for a few seconds then back on and the lights were off and the code was gone but the headlight adjustment wouldn't set and the suspension went wonky so I cycled it both ways. Another off and on and all seemed well.
Took it for a 50 mile ride and the voltages are good and steady, everything electrical is brighter and faster, the tranny is shifting like it used to and it just generally feels better. FWIW all of the parts that I think were spazzing are either Denso or Bosch so most of us probably have similar parts in our cars, we all have a canbus network, so if you're going through weirdness try some of these reset things before firing the parts cannon. Hopefully this works for me (for a while) but I'll probably get the battery tested to make sure it didn't get injured but AGM batteries are usually pretty tough.
-
06-18-2022, 11:37 PM #3702
Had the same experience with some lower shock bolts a couple years ago. Turns out it was a well known issue with those, and if you went searching for people asking for advice on them, a sawzall or grinder was always the recommended solution.
Did a little work on the wagon today. Replaced the fog lights which were both broken. Changed out some hoses and clamps in the power steering since I've been fighting a bit of a whine when it's hot. Could be sucking some air on the return side somewhere maybe, could just be a whiny pump. I haven't heard of a PS pump going out on any of these but I guess anything is possible. I'm trying some slightly thicker fluid too, just to see if it helps.
Also, change your fuel filters people.
-
06-19-2022, 06:53 AM #3703skier
- Join Date
- Dec 2002
- Location
- The Garden State
- Posts
- 4,771
Plenty of truth in this statement- As a shop owner my dream week would be brake jobs as far as the eye can see. My main guy can fix anything- he’s got everything in the bag - troubleshooting/fabrication/ingenuity - worked with this guy for over 16 years there nothing he can’t fix - without time; that’s where the finite resource of time comes in - he’s hourly - I’d never be able to bill all of his time on some jobs where he has to really grind it out. But I’ll gladly eat that time that isn’t billed because I know it’s fixed and not coming back. When I call a customer to explain what we’re doing I can be sure I’m telling him the correct info. Reading coxy’s posts he’s of the same ilk- very few out there can play above the rim in our world- changing parts is easy - figuring out why your changing them isn’t.
Adiron- have you changed the hoses yet on that jeep?
-
06-19-2022, 07:39 AM #3704Registered User
- Join Date
- Mar 2009
- Posts
- 3,281
-
06-19-2022, 09:24 AM #3705Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
I understand the lack of profitability in so many jobs so I ask for help. As often as not I don't understand what's being said or can't figure out how to get to something because I don't know how things come apart. So I'll ask the same thing, sometimes differently, in different places hoping someone explains it so I get it. Trying to learn other aspects from watching videos doesn't usually cut it, they'll say 'just remove xx and yy' without showing it so I'll ask again.
Had someone pointed me in the right direction with my most recent issue I could've saved $400 but time is money. Thankfully there are guys like cocximus that can express their experiences so goofballs like me can do some good with it.
-
06-22-2022, 07:08 AM #3706
Figuring out marine diesels has been not exactly fun, but interesting. Twin 370hp Cummins 6BTAs. Had to rebuild a water pump and have a heat exchanger custom made before getting going this year, working around one small part that was backordered since October due to supply chain issues combined with the surge in Covid boat-buying. Wish I had arms about 3 inches longer and 2 extra elbows to work on the outboard undersides of the Port engine where the raw water cooling pump lives. Engine mount had to come out too. Never appreciated the amount of space in a car engine bay more than this Spring, that's for certain. Oh, and batteries cost WAY more than they used to (or should)...
-
06-22-2022, 09:39 AM #3707
From the tech's perspective, I get that. However from a long term business perspective, it's also short sighted. If a shop can't prove their worth on helping me out on some of the smaller, less profitable (but PITA) jobs, then how can I trust they're capable of doing the BIG, more profitable jobs correctly. When I need an engine or trans swap, every shop that wasn't willing to help me on stupid Euro finicky stuff obviously doesnt earn that job. Always gave me the impression that they're some domestic-only yokel too incompetent to handle more "difficult" European idiosyncracies. Especially when I end up tackling them on my own (no thanks to the shop) and it ended up being super easy and WOULD have been a profitable, quick little job for the shop. I guess that's where the guys who specialize in a particular brand can do really well. They're not afraid. Except the dealer. Those guys remain clueless as ever. Lol.
Sent from my Pixel 3 using TGR Forums mobile app
-
06-22-2022, 10:07 AM #3708Registered User
- Join Date
- Mar 2009
- Posts
- 3,281
Did you like it when potential customers came in to pick your brain and then shopped you to death ? I see both sides because I like to tinker on my own cars but I work at an office that does equipment repair and the volume of cockroaches that want free advice can be overwhelming and when it's time for an actual repair they'll go to the lowest common denominator. Another factor is if the "customer" has already started the repair and fucked shit up it can become a nightmare no shop wants to deal with. "uuh, it was running fine before I brought it in to you guys"
-
06-22-2022, 10:18 AM #3709
I've found that giving all of my repair business to the same shop and delivering doughnuts in between visits pays off in the quality of service. And when/if the shop screws up being reasonable helps.
Seeker of Truth. Dispenser of Wisdom. Protector of the Weak. Avenger of Evil.
-
06-22-2022, 10:20 AM #3710
Lol. I can definitely see your point. Some customers really are a PITA and might cost more in the long run than it's worth. However, sometimes earning a solid rep might be worth it? I guess that is if you don't have a backlog of cars months long to work on. Yeah. I guess I can see both sides.
Sent from my Pixel 3 using TGR Forums mobile app
-
06-22-2022, 10:26 AM #3711
-
06-22-2022, 10:47 AM #3712
-
06-23-2022, 10:45 AM #3713Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
I wish I had a tire mounting machine and a balancer. The cost to get this done now is crazy. #Ineedagarage
-
06-23-2022, 11:12 AM #3714
#LIFEGOALS
Sent from my Pixel 3 using TGR Forums mobile app
-
06-23-2022, 11:43 AM #3715
-
06-23-2022, 12:23 PM #3716
-
06-23-2022, 12:46 PM #3717Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
I had to swap tires from one set of wheels to another so it was removing 8 and mounting and balancing 4. With the disposal fee it was $220. Ouch. I also want a brake rotor lathe. I have a few sets with almost no wear but with hot pad residue and some runout they make the cars shake. If I could just clean them up it would save hundreds.
-
06-23-2022, 12:49 PM #3718
I hear ya, gravity. One of my goals in life is to have my own shop with a lift and pretty much all the tools short of an alignment rack.
Sent from my Pixel 3 using TGR Forums mobile app
-
06-23-2022, 12:52 PM #3719I drink it up
- Join Date
- Oct 2002
- Location
- my own little world
- Posts
- 5,866
I’m going to suggest, gently, that Montucky is nobody’s idea of a profitable, low-touch customer.
focus.
-
06-23-2022, 12:53 PM #3720Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
There was a whole round of shop equipment that sold off cheap 2 years ago as a bunch of older guys bailed out and sold their properties during COVID shutdowns. Around here I expect another round soon as all the guys that opened their shops in the 70s and 80s age out.
-
06-23-2022, 12:54 PM #3721
When you buy a new car in some states, there's an upfront tire fee you pay. Then they charge you again when you dispose of the same tire.
"timberridge is terminally vapid" -- a fortune cookie in Yueyang
-
06-23-2022, 02:03 PM #3722Registered User
- Join Date
- Mar 2009
- Posts
- 3,281
-
06-23-2022, 02:37 PM #3723Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
The tires had to come off the extra wheels because two of them are slightly bent and make the car shake so I bought another set. The replacement wheelset I picked up had a pair of lightly used Nokians that I ran for almost 30k and now it's time to put the 10k mile tires from the bent wheels on the good ones. The bent ones will now head off to get straightened, then I'll restore and paint them before they become the primaries again when these tires wear out.
-
06-24-2022, 12:11 PM #3724Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
Today I learned how easy it is to change the pads in 4 pot Brembos. Pop the pin and the pads just slide out (with a bit of persuasion). Seating all 4 pistons equally is another thing but I figured it out. I forgot to pop the reservoir cap off before I started and when I pushed the pistons back in the second one a bit of fluid forced its way past the cap and came out. The level is perfect now so no problem there but did I damage the seal on the cap when the fluid went by it?
This morning it threw a P0172 code, rich bank 1. I noticed a few days ago at very low speed under load it's pinging a little. I have no idea what kind of miles are on the plugs but that used to be where I'd start. Is that still the same? I always run 93/premium.
-
06-27-2022, 09:48 AM #3725Registered User
- Join Date
- Jan 2014
- Location
- Gaperville, CO
- Posts
- 5,849
Spent the last week wrenching every night on this. Often til midnight or later. Yesterday afternoon we crossed the finish line after some 2300 miles of rallying from Rhode Island to North Dakota.
Lots of firsts...adjusting an external valve train, rebuilding band and drum brakes, replacing chains (vehicle is a chain drive) and mounting tube tires on split rims. Plus lots of other stuff...daily oil and water, repacking bearings, greasing suspension, cleaning / re-gapping spark plugs....
Bookmarks