Results 2,951 to 2,975 of 5882
-
10-12-2021, 05:36 AM #2951Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
Apparently there are only a couple of factories in the world that produce brake rotors and they are all in China. Obviously there are varying quality levels etc. but the differences, supposedly, aren't as significant as we think. IOW they're all shit. FWIW Powerstop is Centric just advertised differently. Has anybody noticed that there's a rotor shortage? I have to do my rears asap and haven't been able to get anything good locally for about a week, only base level, uncoated ones. I have one more option I'm trying in a few minutes when they open so I can do it today's otherwise it's off to Rock Auto land. Sux because I have to what's going to be a shaky 700 mile road trip tomorrow up to the 'daks.
-
10-12-2021, 06:49 AM #2952
Call around to indie shops that have parts departments if you have any around you. When I did my brake job last time, ends up that RockAuto sent me the wrong size for the rears. Their customer service thankfully owned up and gave me a refund right away without any trouble, but they didn't have any of the right ones in stock and I needed my car back on the road stat. Found a Euro shop who not only had the factory rotors in stock, but they were also surprisingly inexpensive, being only about $10 more than Rockauto for the pair, although to be fair my Rockauto ones were the cross drilled "performance" rotors over my factory ones (which were just fine tho). I'll just go to them next time if my car even makes it to its next brake job. Haha.
-
10-12-2021, 06:49 AM #2953yelgatgab
- Join Date
- Oct 2002
- Location
- Shadynasty's Jazz Club
- Posts
- 10,249
Wrenchin... Adventures under the hood... Put em here.
Replaced front and rear on the MILs Impreza recently. I think time was a factor, so I went with a PowerStop kit (ceramic pads, coated rotors, grease, etc) from Amazon. PowerStop can be hit or miss, but this one was a hit. The rotors were new and straight and the pads fit properly, everything new and shrink wrapped, nothing rusty or obviously used/reman’d.
Remind me. We'll send him a red cap and a Speedo.
-
10-12-2021, 07:00 AM #2954
Yeah. My experience with the brand was good too. Although, there's enough stories of misses out there for me to know the brand isn't perfect, but I'd buy them again. Was handy the kit comes with everything needed, including instructions, which I needed being my first brake job attempted.
-
10-12-2021, 09:17 AM #2955Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
I went through the options and everything came out $100 higher, some were a lot more than that, this time and most of those were for uncoated rotors which rust away to dust in a year here. Ehh whatever, I got new parking brake hardware and pads and the wear sensor wire for $80 less than the Auto Zone Duralast Premium stuff so it's a win but I won't have it today before my road trip. I'll think of the wobble as if it's a back massage and just let it shake mildly down all the big hills
-
10-12-2021, 09:39 AM #2956
-
10-12-2021, 09:45 AM #2957
So a pattern is now repeating in my life:
I have old machines: terminally rusty 94 Toyota 4x4, 79 F250 work truck, 86 Honda cb450…I am not a mechanic, but I’m handy and I have access to mechanic friends for advice, I more or less know how to handle the things that come up with these old machines.
I sell them to somebody local, I tell them everything I know about the machine, stuff I think may come up, stuff I’ve worked on, etc. New owner ends up being in over their head with the necessary awareness and maintenance and tlc these things require, then I get ongoing messages and calls as small stuff comes up. The electric fan isn’t working: check the ground. It’s leaking oil: maybe from the timing cover. Transfer case linkage feels sloppy: look at all the linkage pins and the plastic bushing at the lever pivot. It’s running hot with the plow attached at highway speed: put the blade in the bed for long highway trips. I’ve taken the trucks back and fixed stuff myself. I’m storing the motorcycle in my garage for the buyer. I try to help with advice and whatever I know about the machine, etc…but there’s always a tone of, like, hey this thing has problems now, wtf.
I resist telling these guys: a clean version of that thing goes for 5-10x what I sold it for, you drive it around for years/months/whatever, this stuff comes up with old machines…it’s all part of the deal.
It’s frustrating, none of these were dumped with hidden problems, but that becomes the passive-aggressive implication. I’ve been buying and driving/riding old junk since the early 90s and only rarely have I reached out to a seller with a problem, and that was a same-day thing with a dealer.
Part of it, I think, is a small-town dynamic where we’re used to being more accessible to each other (about a lot of things)…but at some point I always find myself wanting to say look, when I had it stuff came up too, when I sold it, it was partly to move on, and part of what made me good at keeping it roadworthy was that I was the one driving it and passing close attention to it…that’s you now.
What strategies, if any, do you guys employ to avoid this kind of ongoing quasi-responsibility for rigs you’ve sold?
-
10-12-2021, 09:58 AM #2958
-
10-12-2021, 10:00 AM #2959
You've already tried what I do, which is being super straight forward about the issues (always a good policy!), but perhaps what helps is I use a Bill of Sale that makes it abundantly clear the vehicle is being sold AS IS, with the following language: "The Vehicle is being transferred on an “AS IS” basis, with no warranties, express or implied, as to the condition of the Vehicle."
And then they have to sign it as buyer, along with me as seller. Never gotten so much as a follow-up text after that, so maybe it helps? I've had good luck selling my junkers. In fact, I JUST sold one of my vehicles on Saturday. I was stoked to get anything for it. Dude was stoked to buy it, even with yet another blown transmission. Everybody wins!
-
10-12-2021, 10:01 AM #2960
I usually never hear from my buyers either but for the last 6 months the guy who bought my Sportsmobile keeps asking me questions. Same MO of they don't seem to understand that it is their turn to figure things out in maintaining an old vehicle. I gave you the service manual and an entire notebook of all the service done...and you clearly don't read them and if you do you don't comprehend.
My last message was "I guess you have it figured out then". I hope he gets the point that anymore questions and Im going to start charging consulting fees.
I also point people to forums and especially YouTube. People want instant gratification so YouTube seems to give them that more than a Google search with too many hits.
Deep down I want to think people are getting smarter but in reality people are getting more dumb being so dependent on information they don't even make time to process. Like global ADHD.
Sucks being a nice guy who knows his stuff doesn't it?
BTW they don't call you. They text and email you. Modern times
-
10-12-2021, 10:08 AM #2961
-
10-12-2021, 10:52 AM #2962______
- Join Date
- Aug 2020
- Posts
- 1,218
I guess if you have a relationship you need to maintain then you answer the question.
Otherwise, it ain’t mine anymore. I have my own problems to deal with. It’s not like I’m trying to maintain some sort of Craigslist reputation or something.
I also do what Montucky mentioned, which is a simple bill of sale and get the title paperwork filed ASAP.
-
10-12-2021, 11:14 AM #2963
Make them sign a note that says the seller understands they are buying this vehicle for parts and that it is not safe to drive.
Just tell them it is to protect yourself and you can't sell the car to them unless they sign.
I did that with the one car I sold that still ran. They had no problem signing it.
Of course they did actually part it out. But the thing would still do 144 mph so if the 18 kid did a high speed run on the way home and the subframe flew apart I was covered.
Should keep them from hassling you. You mean that parts car I sold you?
Sent from my SM-G991U1 using Tapatalk
-
10-12-2021, 11:23 AM #2964
I've sold a few cheap vehicles and bikes and only had one person contact me after the sale, a friend. Bike had some minor damage I forgot to disclose and he didn't notice. He had had the bike 24hrs and already destroyed the derailleur so I pretty much told him, sorry partner.
When I sold my rusty ass montero sport a few years ago, the guy paid in advance and came to pick it up from WY in the dark. Drove it around the block onto the trailer and was talking about doing body work on it . Was half expecting a phone call the next day.
-
10-12-2021, 01:37 PM #2965Registered User
- Join Date
- Mar 2009
- Posts
- 3,281
I would follow the first part of disclosing as much info as possible with a closing of you are buying a used POS for just a few bucks AS-IS so don't expect post sales support or refund. If you want something better go spend more money or pay an expert to check it out before the purchase. Maybe have the potential buyer watch the Brady Bunch episode of "caveat emptor" as part of the prepurchase protocol.
-
10-14-2021, 10:09 AM #2966Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
I always write on the bill of sale "Vehicle is sold AS IS. There are no warranties implied or expressed." Here in NY they have to sign and date the bill of sale and I make sure they see that. I've never heard back from the people I've unloaded my heaps on after the sale even though I know the vehicle is doomed. The last few had to be towed away so that helps...
I pulled everything apart to do pads and rotors and a few other little things while the rotor is out of the way and doesn't it figure some joker stripped the rotor bolt and it doesn't come out now. Looks like I'm crossing my fingers an ez out does the trick (but I don't think it will). Any other ideas before I make it harder on myself?
-
10-14-2021, 10:18 AM #2967
Pound a torx socket bit into the head, it should grip. Maybe hit the thing with a propane or mapp torch first if you think it's rusted.
Worst case, you drill off the head of it and it'll pop off. Don't replace that bolt, it serves no purpose. Lugs n wheel hold the rotor on, not that little thing
-
10-14-2021, 10:21 AM #2968
Lots of YouTube videos specifically about getting a broken rotor removal bolt out.
It shouldn't be too hard as it isn't holding anything. You can drill it away or try an ez-out
-
10-14-2021, 10:28 AM #2969
-
10-14-2021, 10:40 AM #2970
-
10-14-2021, 11:27 AM #2971
Installed a hitch on my Chevy Cruze 6MT. Very straightforward video on etrailer dot com. Took about an hour for the hitch, and another 30 minutes for the wiring. Now I don’t have to borrow my brothers pickup to launch my boat.
Sent from my iPhone using TGR Forums"Zee damn fat skis are ruining zee piste !" -Oscar Schevlin
"Hike up your skirt and grow a dick you fucking crybaby" -what Bunion said to Harry at the top of The Headwaters
-
10-14-2021, 01:26 PM #2972Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
Perfect. Thanx all.
-
10-14-2021, 01:35 PM #2973
This is the RR?
Cut a slot in it with a dremel so that you can fit a screwdriver blade in there. Hit it with a bit of heat from a propane torch and tap the screwdriver ccw with a hammer and it should give up."timberridge is terminally vapid" -- a fortune cookie in Yueyang
-
10-14-2021, 02:05 PM #2974
If I recall correctly, those centering screws had a bit of blue loctite on them from the factory. I always had to use an impact screwdriver to get them out. Have had to use all the tricks listed above on them before too on the stripped ones. Put them back in. They center the rotor and can cause squeaking/squealing on especially with brembos.
-
10-14-2021, 03:57 PM #2975Registered User
- Join Date
- Apr 2004
- Location
- Southeast New York
- Posts
- 11,818
Bookmarks