Results 651 to 675 of 984
-
12-26-2021, 10:10 PM #651Galibier Designcrafting technology in service of music
-
12-26-2021, 11:57 PM #652
Does the brake holder template seem a bit off to anyone else? Went to mount my CAST setup today, but noticed that the template available from their website isn't lining up properly with the FKS/Pivot template I've used several times. I've noted my measured values in between the holes, and Pivot template values off to the right, in a box.
Yes, I've checked my scaling, and the 80mm at the top of the page measures exactly 80mm with my calipers.
I'm thinking just center the bottom two holes as best as possible and send it? As long as the vertical (tip to tail) distance is correct on this template, everything should be good, right?
-
12-27-2021, 12:00 AM #653
You don't really need that template (unless something changed in the last two years)
Mount the heel, push the brake holder towards the heel piece, and use something sharp to mark the holes
-
12-27-2021, 12:10 AM #654King potato
- Join Date
- Feb 2011
- Location
- BC
- Posts
- 1,947
Fucked up a cast mount today first time in a while. Toes didn’t go in straight and I drilled the brake holder holes crooked. Buffed it out but damn it’s still a bummer.
-
12-27-2021, 12:12 AM #655
-
12-27-2021, 12:16 AM #656
-
12-27-2021, 02:31 AM #657Registered User
- Join Date
- Oct 2017
- Posts
- 2,304
drill the holes 39 and 55 mm ahead of the center of two front holes on heel on the ski's centerline, and they're in the right spot re
-
12-30-2021, 12:54 AM #658
-
01-25-2022, 12:08 PM #659Registered User
- Join Date
- Nov 2017
- Posts
- 81
Any ideas what the hell is going wrong with my CAST setup? The tech toe is nearly impossible to slot in, to the extent that I am having to use the hammer end of my ice axe to knock it in to achieve a sketchy tour mode. I have moreover had the whole Pivot toe fly off the front of the ski when hitting a compression at speed, causing a spectacular yard sale.
Is this a mounting error? A problem with the CAST components?
-
01-25-2022, 12:38 PM #660
Post photos, but that sounds like mounting error.
Things to look for:
1) All four holes need to be drilled very straight and in the right spots.
2) The screws need to be installed straight and flush. Any angular misalignment and you're going to have a bad time.
3) If the toe plate is installed over any old holes, they need to be trimmed flush so that there's no protrusion above the main surface of the ski. Little bumps there will deform the mounting shim and you'll have a bad time.
-
01-25-2022, 12:50 PM #661Registered User
- Join Date
- Mar 2020
- Posts
- 209
Any tips to correct my insufferable brake retainers from popping up every 5 mins? I've just reverted to using ski straps to hold my brakes up now.
I heard there was a trick to unscrew the climbing bail/brake retainer piece, re-glue, re-screw, and allow to set with the brake retainer engaged... So I tried that at the beginning of the season and it made no difference... Love the system, but annoying to have to use ski straps on every single transition...
-
01-25-2022, 01:12 PM #662Registered User
- Join Date
- Nov 2017
- Posts
- 81
-
01-25-2022, 01:56 PM #663
Just did 2 new mounts last week. I finally clued in and used the "click in the touring toe while the glue is curing" trick. Both ended up super easy to engage. Alignment is very key for this part of the system.
If your touring toe piece is coming off while your boot is clicked in, then something is wrong. There is a little curved spring that engages behind the front two screws and should prevent this when you are clicked in. Sometimes a few cycles on the bench while pushing the spring back with a screwdriver will ease the fit.
Wait - I just reread Jack Skier's OP, and it's the ski toe that's coming off when you hit a compression? - I can't even imagine how this is possible unless the binding releases your boot first. Then if the binding isn't properly engaged with the posts, I can see how it might come off. On one set of my skis, I have to make sure that my Pivot toes are properly clicked into place, otherwise simply tapping the tails on the ground to remove snow can knock the toe off.
Sounds like a mount error to me. Hopefully can be fixed by a reset of the screws.
-
01-25-2022, 01:59 PM #664
-
01-25-2022, 02:16 PM #665Registered User
- Join Date
- Nov 2017
- Posts
- 81
Thanks for your help. To clarify, I have had problems attaching the tech toes; I am not able to get the curved spring to engage at all, even with the aid of a hammer, the result being that the toe pins do not fully attach to the boot inserts unless I force the toe to lock, and then I have a makeshift tour mode that I would not trust on anything more than a simple approach. On one instance the pivot toe piece blew out, this was due to it not being engaged fully on the posts, I think. To my mind this all boils down to skew whiff toe pillars, but I'll see what the shops says.
-
01-25-2022, 02:45 PM #666Registered User
- Join Date
- Nov 2009
- Posts
- 829
I’ve had every mount issue imaginable, and can pretty safely say that if the Pivot toe pops off while skiing, it’s because the toe piece is not fully engaging onto the shoulder screws, meaning it doesn’t lock.
You’ll likely need to loosen the shoulder screws and retighten while the toe piece is on to get them totally straight. Then while testing them out, pay careful attention to the position of the lock and ensure it’s 100% engaged while on the ski.
I’m also in the camp of my brake retainers not working at all well—have reverted to ski straps, but that’s annoying for quick laps.
Sent from my iPhone using TGR Forums
-
01-25-2022, 04:52 PM #667
Check your print scale + measure your print with a digital caliper before punching the holes. Seems ok to me. Worse is the fact that they didn't include a centerline on the template. I sketched one in so I didn't have to try to center that thing over the heel holes.
You can cheat the heel back a mm or two by pushing the lifter back in to the circular plate, it will move back against the forward pressure tension.
Sent from my SM-G965U using Tapatalk
-
01-25-2022, 05:33 PM #668
No doubt the pillars are either not vertical or not located correctly. As previously mentioned the ski surface may not have been flat (volcanoes on current holes due to not tapping, old plugged holes).
If I was going to try to rescue the mount, I'd:
1) Remove the toe pillar screws and the plate, and scrape/sand the topsheet perfectly flat under the plate
2) Put some waterproof epoxy in the holes
3) Put the plate on the topsheet and carefully rethread screws through the posts in to the existing holes, not tightening completely
4) Slide the tech toe on to the pillars and begin gradually tightening the screws. If you get them mostly tightened down and it's impossible to remove the toe, experiment by loosening one at a time till you can remove it. Experiment with tightening and loosening a few times (with the toe piece in place). It can help pull the problem screw(s) toward vertical.
5) Once you find the magic combo that allows either tech toe piece to be installed and removed fairly easily, check both alpine toes to verify the same.
6) If it all works, reinstall the tech toes while the epoxy is curing.
7) If it doesn't work, you may have to redrill the holes elsewhere or redrill the existing holes for inserts.
Sent from my SM-G965U using Tapatalk
-
01-25-2022, 05:39 PM #669
Me too. Haven't figured it out yet. I did notice that it's not a problem on one one ski (MB 116c with 115mm brakes, older style heel riser plate without plastic on the hold down tab) but it is on the other (Renegade, 122mm waist, 130mm brakes, newest riser plate).
Just another data point... Maybe it's the newer style hold downs, maybe it's the extra overhang of the brakes on the rens.
Sent from my SM-G965U using Tapatalk
-
01-25-2022, 05:59 PM #670
Reading this is why I bought Duke PT16s for my Renegades.
I don’t have a house with a shop anymore. And no local shops gave me confidence to mount the CAST correctly.
Hope it works out._________________________________________________
I love big dumps.
-
01-27-2022, 07:03 PM #671Registered User
- Join Date
- Jan 2009
- Location
- Golden, BC
- Posts
- 298
I’ve also run into issues with several cast tech toes this year. In every case the tech toe base thickness was off by .1mm or more. I had to sand down the base of one of my personal tech toes just to get it to engage properly. The mount wasn’t the issue in any of these cases.
Sent from my iPhone using TGR Forums
-
01-27-2022, 07:17 PM #672Registered User
- Join Date
- Oct 2004
- Location
- Seattle
- Posts
- 3,763
Just did a mount this week and haven't gotten the skis out on snow yet, since we haven't had any in weeks. Both toes were tough to get on at first, but after putting on/taking off a couple of times, it became much easier. Brake lock engaged well, so hoping it turns out OK. Will hopefully find out next week.
-
01-27-2022, 09:11 PM #673
^^ Hot stuff!
-
01-27-2022, 09:16 PM #674
-
01-28-2022, 11:37 AM #675Registered User
- Join Date
- Nov 2017
- Posts
- 81
Quick update on this. I took the bindings to the shop, and we tried several different CAST tech toes from previous production runs; these worked fine. After further investigation we concluded that the metal latch that slots behind the front pillars was getting caught and preventing the tech toe from fully reclining and engaging, with a tap to knock it back it worked properly. Likely a machining error I guess, but still not ideal; a lot of money spent and I now have a chewed up tech toe from hammer hits (the metal on these is surprisingly soft). I am assuming the pivot toe release was user error as I have been skiing them hard since with no issues.
Bookmarks