Page 7 of 7 FirstFirst ... 2 3 4 5 6 7
Results 151 to 168 of 168
  1. #151
    Join Date
    Mar 2009
    Posts
    2,516
    I'd just seal that one up and clamp it. Do your best to get epoxy to wet out the delam

  2. #152
    Join Date
    Mar 2009
    Posts
    2,516
    Does the sidewall sound hollow if you tap it w/ a screwdriver handle?

  3. #153
    Join Date
    Mar 2009
    Posts
    2,516
    Tuco's Edgewerx back in businessClick image for larger version. 

Name:	PXL_20210330_231030773.jpg 
Views:	74 
Size:	2.16 MB 
ID:	369808Click image for larger version. 

Name:	PXL_20210330_231034708.jpg 
Views:	72 
Size:	1.00 MB 
ID:	369809
    Straighten edgeClick image for larger version. 

Name:	PXL_20210330_231902756.jpg 
Views:	65 
Size:	1.14 MB 
ID:	369810Click image for larger version. 

Name:	PXL_20210330_233035670.jpg 
Views:	65 
Size:	1.21 MB 
ID:	369811
    Marking opposing ski to cut matching sidecut to repair mayerialClick image for larger version. 

Name:	PXL_20210330_235216436.jpg 
Views:	63 
Size:	1.31 MB 
ID:	369812Click image for larger version. 

Name:	PXL_20210330_235400106.jpg 
Views:	62 
Size:	1.76 MB 
ID:	369813
    Line up repair material to remove damaged baseClick image for larger version. 

Name:	PXL_20210331_001854495.jpg 
Views:	61 
Size:	1.57 MB 
ID:	369814

  4. #154
    Join Date
    Mar 2009
    Posts
    2,516
    More pics coming later

  5. #155
    Join Date
    Jan 2019
    Location
    59715
    Posts
    4,047
    Shark attack?

  6. #156
    Join Date
    Mar 2009
    Posts
    2,516
    Fellow maggots spliboard, but yes

  7. #157
    Join Date
    Nov 2020
    Posts
    1

    Any tips?

    Whacked my ski good.

    Both edges are blown out a little, but seem to be solid still-- so I just plan to bend those back into place and then put two long base material patches down both sides of my ski. Not sure about delamination/if I should do anything special about the fact that the base is bubbled 1-2mm lower than the edge (you can also see the stress marks in the sidewall, which spook me a little).

    This is my first real surgery outside of binding mounting/ski tuning so I'm a little nervous to just dig in with a knife but this thread is super helpful so thank you! Just wondering if you see anything I should pay particular attention to here or if it is pretty straightforward? Also, is there anywhere to pick up base materially locally (REI, maybe my local ski shop will sell it, I dunno) or should I get the stuff from tognar? Thanks in advance.

    I am working on figuring out how to get the pics embedded on here. Maybe can't post pics because I'm new? They are at imgur(not .net)/a/ID8cINt

  8. #158
    Join Date
    Sep 2019
    Location
    Bay Area
    Posts
    324
    I came into some skis that I want to give to a friend, but which have a small edge compression/crack (pics). Base and sidewall seem intact. No sure what the preferred repair would be, squirt some epoxy in there? Replace a section of the edge? Not worry about it until it gets worse? WWTD (what would tuco do)?

    Thanks all!
    Click image for larger version. 

Name:	IMG_20210414_171628.jpg 
Views:	50 
Size:	1.00 MB 
ID:	372521
    Click image for larger version. 

Name:	IMG_20210414_171606.jpg 
Views:	51 
Size:	1,015.7 KB 
ID:	372520

  9. #159
    Join Date
    Mar 2009
    Posts
    2,516
    You can see the seal is broken from base/edge and edge/sidewall. I'd straighten out that edge. Once it's straightened, it'll be easier to get epoxy in there. Work epoxy into delam well then clamp and continue heat until cured.
    Also if you can tap sidewall w/ screwdriver handle and it sounds hollow, you're probably best off going base patch route so sidewall can be addressed

  10. #160
    Join Date
    Sep 2019
    Location
    Bay Area
    Posts
    324
    Quote Originally Posted by tuco View Post
    You can see the seal is broken from base/edge and edge/sidewall. I'd straighten out that edge. Once it's straightened, it'll be easier to get epoxy in there. Work epoxy into delam well then clamp and continue heat until cured.
    Also if you can tap sidewall w/ screwdriver handle and it sounds hollow, you're probably best off going base patch route so sidewall can be addressed
    Awesome, thank you!

    Sent from my Pixel XL using TGR Forums mobile app

  11. #161
    Join Date
    Mar 2009
    Posts
    2,516
    Welcome.
    Straighten edge just like that pic up^^^there. Clamp something ridgid to base w/ clamps over where the edge goes straight so you don't further delam your edge

  12. #162
    Join Date
    Mar 2009
    Posts
    2,516
    Bump for the m- series

  13. #163
    Join Date
    Mar 2009
    Posts
    2,516
    Fellow mags split board from shark hunting on Superior!
    Click image for larger version. 

Name:	PXL_20210330_231030773.jpg 
Views:	50 
Size:	2.16 MB 
ID:	389318Click image for larger version. 

Name:	PXL_20210330_231034708.jpg 
Views:	49 
Size:	1.00 MB 
ID:	389319Click image for larger version. 

Name:	PXL_20210330_231902756.jpg 
Views:	43 
Size:	1.14 MB 
ID:	389320Click image for larger version. 

Name:	PXL_20210330_233035670.jpg 
Views:	43 
Size:	1.21 MB 
ID:	389321Click image for larger version. 

Name:	PXL_20210410_161345051.jpg 
Views:	46 
Size:	1.23 MB 
ID:	389322Click image for larger version. 

Name:	PXL_20211016_184853725.jpg 
Views:	47 
Size:	1.82 MB 
ID:	389324Click image for larger version. 

Name:	PXL_20211017_175938761.jpg 
Views:	47 
Size:	1.76 MB 
ID:	389325Click image for larger version. 

Name:	PXL_20211017_175946675.jpg 
Views:	53 
Size:	2.01 MB 
ID:	389326

  14. #164
    Join Date
    Dec 2004
    Location
    SoCal
    Posts
    6,176
    Awesome work.

    I drilled a small hole through the topsheet and used one of those adhesive windshield repair vacuum discs with a Mityvac pump to suck warmed epoxy from along the edge into a small delam once, it surprisingly worked.

  15. #165
    Join Date
    Jan 2012
    Location
    SLC
    Posts
    56
    Big thanks to Tuco for helping repair my spilt (pictured above). Amazing work my friend.

  16. #166
    Join Date
    Mar 2009
    Posts
    2,516
    Thanks!
    You're welcome UD! Have a great season brother!

  17. #167
    Join Date
    Dec 2010
    Posts
    398
    Anybody want to take on a small one? I donít have the skills/patience. 2020 186cm gs skis are otherwise really nice. Hate to just throw them in the closet. $100+shipping?

    Click image for larger version. 

Name:	E47AB811-FEDD-4415-8BAC-9906BF6EAC74.jpg 
Views:	30 
Size:	492.0 KB 
ID:	392254Click image for larger version. 

Name:	38D155CA-79E9-458F-ACC0-5FE8404973B2.jpg 
Views:	30 
Size:	373.3 KB 
ID:	392255
    Click image for larger version. 

Name:	5E849C08-4524-47E0-A0BB-98C28458E1EF.jpg 
Views:	26 
Size:	570.6 KB 
ID:	392256Click image for larger version. 

Name:	CFE14ACF-3EF1-4DE9-98A0-3DDA2E3A0D8C.jpg 
Views:	24 
Size:	612.7 KB 
ID:	392257
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	678A3CEB-6FB2-4EC9-B432-496BE0E9D362.jpg 
Views:	25 
Size:	243.8 KB 
ID:	392253  

  18. #168
    Join Date
    Nov 2010
    Location
    7B Idaho
    Posts
    480
    Just use that on the outside edge and ride like normal? Doesn't seem that bad.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •