Page 100 of 100 FirstFirst ... 95 96 97 98 99 100
Results 2,476 to 2,495 of 2495
  1. #2476
    Join Date
    Apr 2016
    Posts
    53
    Quote Originally Posted by jackattack View Post
    ❅-Pivot 14 (13/14 and newer)
    •8 – 18mm small heads
    •4 – 10mm low heads
    •4 – 16mm low heads
    How do you decide which one to use?

  2. #2477
    Join Date
    Mar 2008
    Location
    northern BC
    Posts
    16,294
    Quote Originally Posted by burrito View Post
    Some questions as a first timer:

    I laid out and center punched my skis last night from a paper template, but one of them had something funky going on. I could use a little advice. Here's what I did, and what happened:

    To find the ski center line I clamped a calipers across the ski (to get a proper right angle) and then measured with a centered ruler. I did this in 5 or 6 spots down the ski and connected the marks with straight edge. After that I double-checked the ski center by wrapping the centered ruler to the edges. The boot center line was screen printed on the ski but only about an inch long, so I used a piece of tape to extend it to the edges. The paper template fit perfectly for one ski, and I used a center punch to mark the drill spots.

    When I got to the second ski, though, I couldn't get the template to align with both the boot center line and the ski center line. What I finally came around to thinking was that the screen printed boot center line wasn't at a right angle to the ski center line (tough to actually measure as I didn't have a protractor handy), so I aligned the template with the ski center and the center point of the boot center line and punched the drill locations.

    Is it normal for a screen printed boot center line to be off by a few degrees? It seems like an easy mistake to make in manufacturing. What's the best way for me to go back and double-check to make sure I didn't somehow screw up the alignment on that second ski? I'm about 90% sure it's fine, but I'd hate to get them mounted only to find my binding pointing cock-eyed. Any help is appreciated.
    Skis have been known to come with the boot center mark off usually fore/aft , the thing to do is measure both skls from tail to the ski center mark to check if they are both the same, sometimes on a popular ski you can find the exact distance in cms posted somwhere by a pro or e-mail the mfger and ask, IME this is the openning step to mounting a binding

    I like using a t-square to draw any lines on painters tape for layout, for any measurment I measure from one edge then measure from the other edge, for the ski cneter the lines are usually at a very slight angle to one another cuz ski edges are not straight due to sidecut so split the difference to draw a line that is 90 degrees to the ski center line, I also twice measure from ski edge either way to find points and do accurate measurement

    I never use those flacid paper templates i just use the boot & binding for the mounting process but you somehow want to check the template to make sure the printer you used to print the template is at the correct size, some of the templates have a scale you can measure with a ruler or use the binding

    go slow drink coffee, some drink beer but IME it takes too long/too many beers to mount a fixed heel binding without a professional jig and the accuracy/quality may suffer

    This ^^ is not true for tele cuz I can mount half a binding in 2 beers,

    in any case it would be impossible to tell if a tele mount is fucked up
    Lee Lau - xxx-er is the laziest Asian canuck I know

  3. #2478
    Join Date
    Dec 2006
    Location
    Santa Cruz, CA
    Posts
    256
    Quote Originally Posted by XXX-er View Post
    go slow drink coffee, some drink beer but IME it takes too long/too many beers to mount a fixed heel binding without a professional jig and the accuracy/quality may suffer
    I did a plywood test mount the other day, so I'm confident the templates are good. The boot center marks were in the same spot fore and aft on the skis, too. Mostly I'm worried that I somehow screwed up the ski's center line and have that second ski marked out of center/parallel. I'm going to repeat the whole process on that one tonight to triple-check things before drilling...This is what happens when you move to a town without a reliable shop.

  4. #2479
    Join Date
    Oct 2008
    Location
    off on yet another Tangent
    Posts
    2,547
    Quote Originally Posted by Speedfreak View Post
    Slidewright has the tool (in a set) but it’s not cheap.
    All you need is a screw and jam nut for installs and removals (should be two nuts on the image):

    Best regards, Terry
    (Direct Contact is best vs PMs)

    SlideWright.com
    Ski, Snowboard & Bike Tools, Wax and Wares
    Repair, Waxing, Tuning, Mounting Tips & more
    Paste 5% TGR Discount code during checkout: 1121TGR
    BIKE TOOL BLOW OUT!

  5. #2480
    Join Date
    Jan 2008
    Location
    Whistler
    Posts
    1,448
    Quote Originally Posted by jackattack View Post
    ❅-Pivot 14 (13/14 and newer)
    •8 – 18mm small heads
    •4 – 10mm low heads
    •4 – 16mm low heads
    Quote Originally Posted by aguo5520 View Post
    How do you decide which one to use?
    18mm are the toes
    10mm are the front heels
    16mm are the rear heels

  6. #2481
    Join Date
    Oct 2014
    Posts
    781

    PSA: Mount your own fucking skis.

    Quote Originally Posted by Alpinord View Post
    All you need is a screw and jam nut for installs and removals (should be two nuts on the image):

    No way. That's the worst piece of advice that won't die

    On the plus side, those items are all available at Ace. But if we are home brewing methods, a flathead screwdriver works better

    Sent from my iPhone using TGR Forums
    Buy used mount your own skis build a quiver

  7. #2482
    Join Date
    Oct 2014
    Posts
    781
    Quote Originally Posted by aguo5520 View Post
    How do you decide which one to use?
    You put the screws through the holes, hold the binding in the air and check


    Sent from my iPhone using TGR Forums
    Buy used mount your own skis build a quiver

  8. #2483
    Join Date
    Oct 2008
    Location
    off on yet another Tangent
    Posts
    2,547
    Quote Originally Posted by margotron View Post
    No way. That's the worst piece of advice that won't die

    On the plus side, those items are all available at Ace. But if we are home brewing methods, a flathead screwdriver works better

    Sent from my iPhone using TGR Forums
    Says the guy who cuts threads on plugs that are to be epoxied.....

    The jam nut works just fine for those who do not have a wide enough flathead or extractor, use QK inserts or have stripped BF inserts. Using a shoulder or nutted screw for installing inserts also works fine if you do not have other options in hand.
    Last edited by Alpinord; 12-04-2018 at 09:33 PM.
    Best regards, Terry
    (Direct Contact is best vs PMs)

    SlideWright.com
    Ski, Snowboard & Bike Tools, Wax and Wares
    Repair, Waxing, Tuning, Mounting Tips & more
    Paste 5% TGR Discount code during checkout: 1121TGR
    BIKE TOOL BLOW OUT!

  9. #2484
    Join Date
    Dec 2006
    Location
    Santa Cruz, CA
    Posts
    256

    PSA: Mount your own fucking skis.

    Boom. No longer a self-mount virgin. Shifts on Bent Chetler 120s. Can’t wait to break ‘em out this weekend.
    Click image for larger version. 

Name:	IMG_3441.JPG 
Views:	72 
Size:	240.5 KB 
ID:	258613

  10. #2485
    Join Date
    Jan 2004
    Location
    SoCal. SoVT.
    Posts
    1,130
    Quote Originally Posted by Alpinord View Post
    All you need is a screw and jam nut for installs and removals (should be two nuts on the image):

    I saw those but the post was asking for the BF tool with the little wings that fit in the insert notches
    Quote Originally Posted by doughboyshredder View Post
    If you're not standing on the fucking traverse with your thumb up your ass you wont get checked.

    dumbfuck.

  11. #2486
    Join Date
    Oct 2008
    Location
    off on yet another Tangent
    Posts
    2,547
    Quote Originally Posted by Speedfreak View Post
    I saw those but the post was asking for the BF tool with the little wings that fit in the insert notches
    Oops cam in sideways to the thread.

    Another option is a modified #8 slotted screwdriver or bit:

    Name:  IMG_5914.jpg
Views: 276
Size:  16.4 KB
    Best regards, Terry
    (Direct Contact is best vs PMs)

    SlideWright.com
    Ski, Snowboard & Bike Tools, Wax and Wares
    Repair, Waxing, Tuning, Mounting Tips & more
    Paste 5% TGR Discount code during checkout: 1121TGR
    BIKE TOOL BLOW OUT!

  12. #2487
    Join Date
    Mar 2009
    Location
    OR
    Posts
    1,250
    Just mounted up the groms new whip. Come to think of it- I was on some POS Mickey Mouse skis at his age. Who says it will be the first gen to have it worse than that last?

    Click image for larger version. 

Name:	IMG_2287.JPG 
Views:	58 
Size:	739.9 KB 
ID:	259295

  13. #2488
    Join Date
    May 2009
    Location
    pdx
    Posts
    10,021
    ^^^ sharp!

  14. #2489
    Join Date
    Oct 2015
    Posts
    47
    Mounted last night 181 Sego Cleaver 102 w Attack 16s
    Click image for larger version. 

Name:	IMG_1694.JPG 
Views:	45 
Size:	1,007.6 KB 
ID:	259598

  15. #2490
    Join Date
    Jan 2008
    Location
    Whistler
    Posts
    1,448
    Mounted some old swiss cheese skis with some long track STH 14s, just so I could have an extra pair of fat skis for visiting guests.
    Had to dig through my spare screws and grind a few screws to make the lengths work. I left 2 rear heels screws 1-1.5mm too long. Bubbled the bases. Oops. (I've mounted thousands of skis in my days, and should have know better but because it was a beat up loaner I didn't really care)
    Had to pull those screws out, grind them down another 1mm. Heat the bases up really warm and pound em down with a flat faced hammer. After a quick scrape with the metal scraper I could hardly tell which ski I screwed up on.
    Reminded me of my shop days when we would charge extra for a mount when we encountered a "Binding in Bag w loose screws". We rarely charged for binding mounts. Our store policy was if you bought a ski, boot or binding from us we would mount for free. If someone brought in an outside ski for mounting we ofter just ask for beer. BUT if it was a binding in bag, or if the customer said "I think all the screws are there" the work order would get a big black Sharpie marker "BIB" written on it, and we charged the full price.

  16. #2491
    Join Date
    Sep 2008
    Location
    NorCal
    Posts
    402
    Need sanity check on this;

    I traded some swag for a pair of 188 Soul 7 HD and mounting Attack 13's and have a Raptor w/303 BSL. Rossi has two recommended mount points: “All Mountain” (5.9 cm from center; 87.3 cm from tail) and “Freeride” (7.9 cm from center; 87.3 cm from tail). I want the freeride or -2.

    I have template; check.
    I've ID'ed the ski center via this mark
    Click image for larger version. 

Name:	IMG_1562.jpg 
Views:	38 
Size:	906.1 KB 
ID:	259646
    To mate the two template half's (for my BSL) using the mm markers I tape together each piece (heel-toe) and match up @ at the 300mm line?
    Click image for larger version. 

Name:	IMG_1563.jpg 
Views:	36 
Size:	995.4 KB 
ID:	259648
    ID ski center (vertical or half)
    Tape template to ski placing boot mid sole mark -2cm behind ski centerline?
    3x measure, adjust as needed, tap, glue, drill, etc.

    Joining the template and properly placing it (for -2 mount) have me unsure. TIA!

  17. #2492
    Join Date
    Mar 2008
    Posts
    119
    Click image for larger version. 

Name:	E0E54D4C-2C60-4254-98DE-3354FC576B80.jpg 
Views:	38 
Size:	411.1 KB 
ID:	259689
    Praxis porn

    Click image for larger version. 

Name:	6C3C3E0A-A854-45C0-9403-8DE2C9A49509.jpg 
Views:	43 
Size:	430.0 KB 
ID:	259687
    Vintage lines found in the garage

    Jus wanna say Thx all for all the comprehensive knowledge on this loooong as thread

  18. #2493
    Join Date
    Apr 2016
    Posts
    53
    So what exactly is the benefit that tapping provides? Why is it needed for skis with metal topsheets? I'm trying to understand the details of it. The only reason I can think of is that a tap has sharper or thinner threads that help cut into the wood layers.

  19. #2494
    Join Date
    Jan 2014
    Location
    Gaperville, CO
    Posts
    3,057
    Quote Originally Posted by aguo5520 View Post
    So what exactly is the benefit that tapping provides? Why is it needed for skis with metal topsheets? I'm trying to understand the details of it. The only reason I can think of is that a tap has sharper or thinner threads that help cut into the wood layers.
    It prevents volcano-ing of the top sheets -- which is more likely with a metal layer.

  20. #2495
    Join Date
    Feb 2010
    Location
    The Chicken Coop, Seattle
    Posts
    2,272
    Most recent work. Get to ride lifts this weekend at last.

    Click image for larger version. 

Name:	IMG_4456.JPG 
Views:	27 
Size:	312.3 KB 
ID:	259709
    Click image for larger version. 

Name:	IMG_4457.JPG 
Views:	27 
Size:	312.7 KB 
ID:	259710
    wait!!!! waitwaitwaitwaitwaitwaitwaitwait...Wait!
    Zoolander wasn't a documentary?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •