Results 3,501 to 3,525 of 6863
-
02-08-2020, 06:57 PM #3501
-
02-08-2020, 09:51 PM #3502
jb weld, with metal repairs it works ok
can't think of a worthy ski fix for the product
the g flex works very well from maintenance to major repairs, would recommend for everything in between
-
02-08-2020, 09:56 PM #3503Registered User
- Join Date
- Jun 2011
- Posts
- 6,177
-
02-08-2020, 10:19 PM #3504Registered User
- Join Date
- Feb 2008
- Location
- Donner Summit
- Posts
- 1,251
Eh, I don't see that much difference between JB and other 2-part epoxies (e.g. Marine Tex) for skis. JB is usually easier for me to find and easy to eyeball the mix (1:1 instead of 1:5 or whatever). I use a finish nail to fill the holes, it works fine.
-
02-09-2020, 12:19 AM #3505Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,060
Would you ever see jb in a real wood shop ?
And btw the eh goes at the the back ehLee Lau - xxx-er is the laziest Asian canuck I know
-
02-09-2020, 07:26 AM #3506
JB Weld and especially marine Tex are not the same as lower viscosity epoxies. Marine Tex is like a putty(think boat repairs) and JB a gel.
I've filled plenty of screw holes w/ JB Weld. Guarantee it's a better seal than a glued in plastic plug(I use those too tho). Wet the hole out as best as possible and fill hole. I use the 5 min shit for this so you don't have to wait forever for curing to start. When catalyzation begins and JB still malleable, take a tamper the diameter of your hole and compress into hole. This should fill hole most of the way up. Then just topcoat w/ more JB.
I've never fixed a spinner with JB, but see no reason why a serviceable repair could not be made(although I would encourage doing it proper the 1st time).
-
02-09-2020, 09:53 AM #3507
Those weren’t mine. The guy was stoked on them tho. The thread about the bindings here on TRG has some stories about breakage, but I thought they’re pretty clever bindings and I’m considering getting some.
https://www.tetongravity.com/forums/...ritschi-Tecton
-
02-09-2020, 10:12 AM #3508Registered User
- Join Date
- Dec 2015
- Location
- Oakland
- Posts
- 150
Anyone got advice for mounting pin bindings? I've mounted up a handful of pivots and aaatacks without much trouble. But someone at a shop was telling me about how much trickier pin bindings are—something about how being just a bit misaligned can cause pre-releases. Got me a bit worried, but this thread has been a wealth of info.
I use paper templates and a drill (though it's possible I could get access to a drill press if I have to). Looking to mount up a pair of dynafit rotations.
-
02-09-2020, 10:16 AM #3509Goal: ski in the 2018/19 season
-
02-09-2020, 10:19 AM #3510
I have been skiing them for two seasons now and like them a lot. Lighter than shifts or kingpins and I have never had a pre release at my "chart" DIN. I ski them in bounds a bunch and forget they aren't an alpine binding.
Sent from my Pixel XL using TGR Forums mobile app
-
02-09-2020, 10:21 AM #3511
Eh. Getting the toe and heel aligned is maybe a bit more important than it is with an alpine binding, but it's still not rocket surgery. You'll be fine.
If you want to be really careful about alignment (depending on the binding you're mounting), mount the toe, then click the boot into it, slide the heel piece pins into the boot from behind, and set the heel piece down on the ski. Use that to check the hole locations. Works better with some bindings than others, depending how much the heel piece covers the screws.
-
02-09-2020, 10:32 AM #3512Registered User
- Join Date
- Feb 2008
- Location
- Donner Summit
- Posts
- 1,251
What works for me (including race bindings with no heel adjustment) is to carefully mount the toe with the template, click the boot in, line up the heel in the boot and make sure it's aligned properly and the heel gap looks right. Mark the holes, drill and screw one hole, click the boot in and make sure it's still good. Take out the boot and drill the rest.
You can also start the other way - mount the heel first, then use the boot and binding to line up the toe.
-
02-09-2020, 10:51 AM #3513
Lol, that's how I do it, except I use a collet instead of a chuck. It's also handy to use a 1/4" end mill if you're doing inserts in holes that were originally done with a jig, so you end up with a square pattern that's centered on the ski (assuming the jig holes aren't too far off and are within the 1/4").
Lemmie know if you want my measurements/coordinates for Salomon & Fritschi, the popular templates tend to round to the nearest mm. Which is fine for wood screws, but can be noticeable if using inserts.
-
02-09-2020, 07:11 PM #3514
Just picked up some J Skis metals at their warehouse sale. Does anyone know what the mounts are? Looks like Telemark but I'm not totally sure
Sent from my SM-G960U using Tapatalk
-
02-09-2020, 07:21 PM #3515
-
02-09-2020, 07:36 PM #3516
-
02-09-2020, 07:44 PM #3517
-
02-09-2020, 10:56 PM #3518Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,060
You can use a template or not but first figure out where fore/aft to mount the heel and put it at dead center, then mount the toe dead center by ONE screw only, allow the toe to VERY slightly rotate around that 1 screw, mark/drill all the rest of the toe piece screws with the boot locked into ski mode and everything should line up perfectly
this will ^^ work for any frame type AT binding where you mount the heel and toe independently but they need to lineup/mesh perfectlyLee Lau - xxx-er is the laziest Asian canuck I know
-
02-10-2020, 09:27 AM #3519
@xxx -er's advice is the way to go (heel first, one toe screw at a time), irrespective of whether or not you use a template.
For toe holes #2-4, I've taken to using a larger drill bit (as close to a perfect fit in the toe piece holes) to "centerpunch" the holes. I drill very carefully - just enough to create a dimple.
For inserts, I've taken to screwing in the binding while the epoxy is setting (remove afterwards for inspection and Vibra-tite). It helps straighten any minor tilting during insertion.
I was always concerned that some epoxy would seep into the threads (overflow), but with care, this won't happen.
Even if you use a tap guide, you can still tilt the inserts a bit when installing them. I use the double lock nut on a screw technique to install them, even though I use BF inserts with the screw slot. It helps minimize tilt in comparison with starting the insert off with the BF tool or straight-bladed screwdriver.
I finish off with a screwdriver (blade ground "fat" to widen it for a good fit) to get the insert 1/3 to 1/2 turn below the top sheet level.
Then ... there's the end mill approach if you own one ;-)
... ThomLast edited by galibier_numero_un; 02-10-2020 at 02:06 PM.
Galibier Designcrafting technology in service of music
-
02-11-2020, 10:10 PM #3520Registered User
- Join Date
- Nov 2016
- Posts
- 1,408
Anything special about what fiberglass cloth you get? I was just going to get the stuff home depot carries: https://www.homedepot.com/p/3M-Bondo...0128/202077813
Sent from my Pixel 2 using Tapatalk
-
02-11-2020, 10:41 PM #3521Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,060
yup that stuff is fine ^^ I just cut it into 1/2 inch lengths wet it out with epoxy and cram it in the screw hole
i also used some to back up the crack in a thule box and probably some other things i don't remmeberLee Lau - xxx-er is the laziest Asian canuck I know
-
02-11-2020, 10:44 PM #3522Registered User
- Join Date
- Nov 2016
- Posts
- 1,408
-
02-12-2020, 02:33 PM #3523Registered User
- Join Date
- Dec 2018
- Posts
- 213
I just ordered a replacement heel for a Dynafit TLT Speed Radical binding that I just broke. I don’t know much about mounting bindings. Anything should know about mounting the replacement heel using the same holes? Use wood glue? Thanks in advance.
Sent from my iPhone using TGR Forums
-
02-12-2020, 03:01 PM #3524Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,060
The screws might be stuck so before you strip the head use use a soldering iron on the head for 10-20 sec to loosen up the screw,
if you don't have a soldering iron turn a 1/4" drill bit backwards in the chuck, run it at high speed to heat up the screw
I would just use the same holes with slow set epoxy
if any of them strip use the FG and epoxy as per above ^^Lee Lau - xxx-er is the laziest Asian canuck I know
-
02-12-2020, 03:04 PM #3525Registered User
- Join Date
- Dec 2018
- Posts
- 213
Bookmarks