Results 1,201 to 1,225 of 1728
Thread: Binding Mount Paper Templates
-
01-05-2018, 11:58 AM #1201
It's better than I remembered - the front two hole pairs (closest to the ski tip) are the ones that are close (but fine, IMHO). Given a choice, I'd rather have the rear holes of the toe piece a comfortable distance from each other (upward force from back seat landings).
I did this overlay from my mounting templates which I proved to work, but as always, I'd appreciate your verifying this before drilling in your skis ;-)
... ThomLast edited by galibier_numero_un; 01-05-2018 at 04:49 PM.
Galibier Designcrafting technology in service of music
-
01-08-2018, 01:30 PM #1202Registered User
- Join Date
- Jan 2018
- Posts
- 2
Marker M1000 paper template
Got here from binding freedom site.
Hope this is the acceptable way to ask my question or was I to reply to threads to earn the ability to post a new thread?
I spent a lot of time searching this forum but did not find.
Looking for paper template or info to mount Marker M1000 bindings.
Or can it be done by carefully placing on the boot, aligning/centering etc. & marking outline/holes, hopefully leaving room for forward pressure adjustment?
Thanks.
-
01-08-2018, 05:54 PM #1203
-
01-09-2018, 11:10 AM #1204
Anyone know what the Salomon Shift mount pattern is looking like? Trying to determine whether or not I'll have overlap issues with my Sego Sloppy Joes currently mounted with Tyrollia Attack 14s.
-
01-09-2018, 10:16 PM #1205
-
01-11-2018, 09:45 PM #1206Registered User
- Join Date
- Oct 2011
- Posts
- 10
I just tried to test mount my salomon STH (14s i think, and year i want to say 2012) on some ply wood with the template from the first page of the thread and it did not work. I only tried the heel plate and the screw holes were too close together by a fairly good margin. I measured the ruler on the printout and its not coming out to 8 inches like its stated though its printed on 8.5 X 11 paper. Has anyone else had this problem?
-
01-11-2018, 09:48 PM #1207
Binding Mount Paper Templates
Print scale needs to be fixed...
Or, you get the toe & heel mixed up?
-
01-12-2018, 09:43 AM #1208Registered User
- Join Date
- Oct 2011
- Posts
- 10
-
01-12-2018, 09:48 AM #1209
-
01-12-2018, 09:59 AM #1210Best regards, Terry
(Direct Contact is best vs PMs)
SlideWright.com
Ski, Snowboard & Tools, Wax and Wares
Repair, Waxing, Tuning, Mounting Tips & more
Add TGR handle to notes & paste 5% TGR Discount code during checkout: 1121TGR
-
01-12-2018, 09:59 AM #1211but not a marker fanboy
- Join Date
- Apr 2012
- Location
- N@
- Posts
- 394
So people here try to help you with what is a rather elementary question, you then respond with sarcasm, and then ask another [what some would call stupid] question? And what's with the recent trend of people just wanting spoon-fed answers without bothering to read and learn for themselves?
But to answer your question, like SoooL stated, it's likely you have the "fit to page" or custom scale option selected in your print settings. Change that to "actual size", reprint, and check your scale again with ruler.
-
01-15-2018, 10:39 AM #1212
Binding Mount Paper Templates
Billy, Neil
I’m coming back to this because it is sticking in my noggin
I mounted with no problem, I thought.
But my BSL is 316. When I first read your post, I thought you might be at an extreme of the range. But it’s just a function of length.
Following the paper template and locating the actual 316 line on the templates (not just going with the closest 5mm line and adjusting from there) put me at the back end of the track. Forward pressure is fine.
Here’s a photo I took when I did a plywood test mount
The more I think about it, I would expect to be in the middle of the track if the template is set up correctly. I’d expect some tolerance to each side (longer & shorter) since I targeted my exact BSL. I was having a conversation about letting my brother try my skis (he’s got a longer BSL) and realized I couldn’t accommodate his boots the way it’s currently set up.
I’m reticent to pull the bindings since they’re working for me, but I think it’s worth a warning for other mags
STH2 template needs an edit, IMO
It seems like the heel needs to move back 10-15mm (or equal toe & heel shift relative to center)
(if I pull these bindings I will certainly come back and offer a proposed update to the template)
-
01-15-2018, 07:01 PM #1213Registered User
- Join Date
- Oct 2011
- Posts
- 10
I really dont understand this. I see so many people respond like this guy just did on this site, they get so upset when they think someones question isnt advanced enough or too "elementary". The person i responded to was obviously was making a joke "maybe you mixed up the heel and the toe" and i made a joke in reply. I have absolutely no ill will whatsoever. My printer was already set to 100% scale so i wanted to double check with people here what to do in this situation. The whole point of this type of thread is to help people, clearly i was confused and dont want to screw up my mount, but because you have decided you are the police of whats a legitimate question and what isnt you come on here and try to demean me for it. Its sort of hilarious, Why in the world would you let this bother you?
-
01-15-2018, 08:19 PM #1214but not a marker fanboy
- Join Date
- Apr 2012
- Location
- N@
- Posts
- 394
You asked how to check/change the print scale, which can be easily found via a quick Google search (as well as the first post of this thread and many more times throughout). You also confirmed that your scaling had already been already set to 100%, although you never mentioned that until this evening. That is what would be an obvious (and likely) culprit -- and is not the same as simply printing on 8.5x11 paper as you repeatedly stated above. After 49 pages, this thread can do without additional questions on print scaling.
So did you get your issue resolved, and if so, what was the problem so other people can learn from your misfortune? If it's not resolved, I would still try selecting actual size for scaling instead of 100% (not sure if that makes a difference), perhaps try a different printer as sometimes they still print a bit off (like one at my work does), or try changing the percentage above or below 100% until it measures out correctly.
And I'm glad you found my previous response hilarious, well sort of hilarious at least. I wish my wife would appreciate my sense of humor more often
-
01-15-2018, 08:32 PM #1215
I've tried several times to print out templates and increased the % to the point where you cannot read the BSL markings anymore and still cannot get 20cm/8inch to line up. Not sure if it's just my printer or if others have had an issue with this.
Sent from my XT1650 using TGR Forums mobile appWhy don't you go practice fallin' down? I'll be there in a minute.
-
01-15-2018, 08:51 PM #1216
I just downloaded and printed the Salomon template from the first page (salomon_paper_template_R6.pdf) and the scale correctly measures 8".
Note: I did have to select "Scaling Type: None" in my print settings.
-
01-15-2018, 11:23 PM #1217
Take the PDF to Kinkos and have them print it at 100% scale on transparency paper. Scaling issue solved, with the additional benefit for the transparency being more durable and easier to work with
-
01-16-2018, 12:22 AM #1218
I dunno where you got the idea of being too far back in the range? I'd say you're spot on the middle. There's even a mid mount mark on the back end of the track (see my pic), right where your worm screw ends in your pic, from there you can adjust another cm back (basically to the end of the flat platform behind the track)...
-
01-16-2018, 09:53 PM #1219
Binding Mount Paper Templates
SoooL, thanks for the response. Shows what I know — first Salomon binding mount for me. How do you know when it’s out the back, then? Do you just run out of movement, ie it locks up?
Last edited by acinpdx; 01-17-2018 at 12:20 AM. Reason: Spelling
-
01-16-2018, 10:58 PM #1220
This will get lost in the thread, but I think there some misunderstanding about scaling and when you might need to change it.
Even if your PDF reader has scaling set to 100% when you print, that DOES NOT mean that the print you get will match in scale to the original PDF. [i.e. 10cm in the designed PDF actually outputs a 10 cm line/dimension.] It should, and probably most of the time it is, or is really close. But not always.
1) Thus, the way to fix/check this is to print with no scaling initially.
2) Now take a ruler.
3) If that 10cm line is 9.5cm instead, then you need to set the scaling to around 105%. If it's 10.5cm [~95%] ... or some other length, adjust accordingly.
4) Now reprint.
5) Repeat steps 2-4 until what prints on your printer matches the given dimensions on the PDF.
Once that's done and they match - print several. Mark them so you know they are the "good" ones, and throw all the tests away - I'd probably suggest shredding them too - you really don't want to pick a bad/wrong one up and use it by accident. [And I know first hand that it's really easy to do. Fortunately I've never actually done a real mount with one.]
The extras save you from having to repeat those steps above, should you need another copy.
HTH
-Greg
-
01-17-2018, 01:23 AM #1221
-
01-17-2018, 02:41 AM #1222Registered User
- Join Date
- Nov 2015
- Posts
- 6
Dear! We need template TYROLIA AMBITION 10 HEAD BRAKE 85 (C) 2017 TYROLIA AMBITION 10 HEAD 2017
Enviado desde mi iPhone utilizando TGR Forums
-
01-17-2018, 02:52 AM #1223Registered User
- Join Date
- Nov 2015
- Posts
- 6
Tyrolia touring
Enviado desde mi iPhone utilizando TGR Forums
-
01-17-2018, 03:56 PM #1224
Anyone have the mojo18 template?
-
01-17-2018, 04:21 PM #1225Registered User
- Join Date
- Jan 2014
- Location
- Gaperville, CO
- Posts
- 5,849
Bookmarks