Binding Mount Paper Templates

[Dog Pound]

I am curious:

Is this the same hole pattern for Atomic/Salomon WTR binding minus the front screw hole?
I could quiver killer the holes and use shifts for touring and WTR for downhill ( maybe overkill though)

[frankfrank]

I made a skitrab vario 2 template based on the powderguide templates. I only verified it with 300BSL. It could be way off with other BSLs. Verify it before drilling. Hole patterns as listed on https://skimo.co/tech-binding-hole-patterns

Link: https://ufile.io/6bsyqbem

Worked great for me. Measurements looked good after printing. Used drill press and tapped holes. Tightened the toe screws while the boot was in place, everything lined up the first time. I set the template at 318 to use with both 314 and longer boots.

[habisy]

Anyone have the templates for these? Is it the same as the "non Carbon" Tecton 12s?

[~mikey b]

the old Tecton 12 and the new Tecton 13 Carbon are the same pattern

just used my Jigarex plates on the new ones

[ski-wpk]

Anyone have a template for Salomon C3 kids bindings? I searched this thread but couldn’t find anything.

Kid 1 is getting older and better on snow so I can’t eyeball a mount anymore.

[Zac]

Was Looking for a template for the Look Team 4 binding. Couldn't find on here so I drew one up.

Cant post a link..

[Dee Hubbs]

What pattern is the Salomon Stage11 using?

[natebob]

I'm trying to print a template for the Meidjo 2.0 and 3.0 from the Meidjo site. It says to "print with no scale". Tried printing with the scale as "fit to page" and adjusting the scale between 100% and 200%, not coming out right. I searched this thread, didn't find any Meidjo templates. Any advice on how to print these things to scale?

[Alpinord]

I'm trying to print a template for the Meidjo 2.0 and 3.0 from the Meidjo site. It says to "print with no scale". Tried printing with the scale as "fit to page" and adjusting the scale between 100% and 200%, not coming out right. I searched this thread, didn't find any Meidjo templates. Any advice on how to print these things to scale?

Send me the link.

[natebob]

Message sent, thx.

[Alpinord]

Message sent, thx.

It scaled fine, but needed to be cropped. Try this.

[natebob]

That will work, thanks a ton!

[N1CK.]

bump.

Did we ever come up with an accurate Tecton template? The few posted in this thread all seem to have the incorrect heel. I have two pair of skis to drill for Tectons (27.5 Zero G, 315bsl) and wouldn't rather not freehand the heels if possible.

Cheers, and thanks.

[Alpinord]

bump.

Did we ever come up with an accurate Tecton template? The few posted in this thread all seem to have the incorrect heel. I have two pair of skis to drill for Tectons (27.5 Zero G, 315bsl) and wouldn't rather not freehand the heels if possible.

Cheers, and thanks.

I believe we got that sorted out here Minimum & Maximum Boot Sole Lengths


https://www.tetongravity.com/forums/....php?p=6743502


Sent from my iPad using TGR Forums

Edit: I shifted the rear holes the 0.5mm for this revised Vipec-Tecton Template:

[Alpinord]

While I'm at it, here is the revised STH2 template per this binding layout tool project.

[N1CK.]

I believe we got that sorted out here Minimum & Maximum Boot Sole Lengths


https://www.tetongravity.com/forums/....php?p=6743502


Sent from my iPad using TGR Forums

Edit: I shifted the rear holes the 0.5mm for this revised Vipec-Tecton Template:

thanks Terry! this one was perfect. Cheers!

[Alpinord]

thanks Terry! this one was perfect. Cheers!

You're welcome. Glad it'll work for you.

[ASmileyFace]

Maybe it's done before, but based on the measurements from Spyderjon and the Binding Freedom paper template for the ordinary Duke I put together a paper template for the Duke PT. Own no binding to test the pattern myself, so make sure to verify before you drill!

Attachment 403875

FYI this template is incorrect.

I built a new template with the Kingpin toe and Jester heel that worked well using this thread. https://www.tetongravity.com/forums/...T-hole-pattern

If I find time in the next week or so I'll try and create a new template for the PT on it's own, but be warned that the link in this thread does not work.

[Alpinord]

FYI this template is incorrect.

I built a new template with the Kingpin toe and Jester heel that worked well using this thread. https://www.tetongravity.com/forums/...T-hole-pattern

If I find time in the next week or so I'll try and create a new template for the PT on it's own, but be warned that the link in this thread does not work.

If you send it to me, I can clean it up if needed and get it posted. There are various other templates that are inaccurate and modified too. I don’t how or when, but I might try to collect them and get them more organized.



Sent via iPhone
Slidewright.com

[~mikey b]

double checking if anyone knows for sure

I was told the Rotation 7 is Rotation toe and Radical heel

anyone know about Rotation 12 heel?

[~mikey b]

double checking if anyone knows for sure

I was told the Rotation 7 is Rotation toe and Radical heel

anyone know about Rotation 12 heel?

still looking

[MottN]

double checking if anyone knows for sure

I was told the Rotation 7 is Rotation toe and Radical heel

anyone know about Rotation 12 heel?

The rotation 12 uses the same pattern as (and is basically the same as) the radical 2.0 , so for templates that is what you are looking for.

[~mikey b]

thanks

I have a set of Rotation 7 jigarex plates, as well as Radical (2.0 I think)

this helps me out

thanks twice

[natebob]

Hi, is there a template for the Atomic/Salomon Backland Tour? I tried searching the thread, didn't come up with anything, but don't think I was doing it right. Thx.

[Alpinord]

Hi, is there a template for the Atomic/Salomon Backland Tour? I tried searching the thread, didn't come up with anything, but don't think I was doing it right. Thx.

Are those rebranded bindings from another mfgr or by Salomon?


Sent via iPhone
Slidewright.com