Results 1 to 25 of 29
-
03-03-2009, 03:10 PM #1
Edge compressed inwards, how to fix?
Hit a rail yesterday, there was a part sticking up, no my edge is compressed straigh in towards the center of the ski, not up towards the topsheet like usual.
Here are some pictures
How should I got about replacing this, i like these skis. the fix has to be strong, it is right under foot, and I hit rails regularly as these are my park skis.The whole human race is de evolving; it is due to birth control, smart people use birth control, and stupid people keep pooping out more stupid babies.
-
03-03-2009, 03:13 PM #2
The only way to fix that effectively is to do an edge replacement. That i think is best done in a shop. You cut out the edge and base in the bad area. You obtain a piece of edge and trim it to fit right. gets some edge screw and screw it in and then base patch or base weld over the edge.
-
03-03-2009, 03:16 PM #3
duker speaks truth, although if that was my ski I would just dull and deburr the edge right there, flatten the base bulge and give'r.
-
03-03-2009, 03:26 PM #4Registered User
- Join Date
- Oct 2003
- Location
- CO
- Posts
- 570
-
03-03-2009, 03:26 PM #5
hammer it down so its flat and fill the sidewall with epoxy and call it good. replacement will cuase more damage and more durability issues than jsut rallying them.
if the are park skis and you hit rails alot, then this is only the first of many anyhow.
less is more.
-
03-03-2009, 03:37 PM #6
Theres nothing really to hammer. the edge stayed flat, just the inward force caused the base to bubble up. I think also, that if i just ground the base there, it would be pretty close to base when done.
How bout cutting some of the base out, and bending the edge as close to straight as I can get, then filling with epoxy/PtexThe whole human race is de evolving; it is due to birth control, smart people use birth control, and stupid people keep pooping out more stupid babies.
-
03-03-2009, 03:39 PM #7
-
03-03-2009, 03:49 PM #8
-
03-03-2009, 06:39 PM #9
Yes do that.
I would try it this way:
Remove the heel piece
Remove some base material.
Get a couple of pipe clamps, and clamp one on either side of that bent edge. (clamp goes from one side of ski to other)
Get a hammer and punch, and attempt to get a localized hit on that bend.
Keep a close look to be sure you are not making it worse.
You won't get it perfect but you might straighten it a bit
File down the remaining burrs/high spots.
Dry the damaged area out real good
fill with epoxy and or ptex. clamp with scrapers if necessary.
After a couple days of curing file/ sand the high spots.
Install heel piece and go.The coefficent of desireability is inversly proportionate to the degree of availability.
-
03-03-2009, 08:26 PM #10
-
03-04-2009, 10:04 AM #11Registered User
- Join Date
- Mar 2008
- Location
- northern BC
- Posts
- 31,081
would a vise be a better way to bend things back and when you do start skiing this ski again mark your skis left & right
make that damaged edge your OUTSIDE edge at all times ...the outside edge doesnt have to take much force ,
unless of course you tele
-
01-08-2020, 10:13 PM #12
Edge compressed inwards, how to fix?
Resurrecting this old thread with the same issue the OP had— edge compression inward toward the center of the ski, base bubbled up. Must have hit a rock from the side. No edge or top sheet cracking, doubt there is structural from what I can tell. Not a park ski, but a beloved thrice drilled Praxis MVP rock ski. Could I just cut out the raised base, epoxy any area that could let water in, ptex, detune and call it a day? In hindsight it did feel a little grabby in certain situations on the ruts/flats as-is. Might notice it more on a groomer, not sure. Didn’t notice it in softer snow.
Last edited by Self Jupiter; 01-08-2020 at 11:47 PM.
-
01-09-2020, 03:35 AM #13Registered User
- Join Date
- Apr 2004
- Location
- Chamonix
- Posts
- 1,012
Don't remove base material. Cut the base perpendicular to the edge about 20mm, peel up two triangular flaps of base, hammer edge back into shape, heat/glue/clamp everything together. Base grind if you're picky.
-
01-09-2020, 07:29 AM #14
-
01-09-2020, 07:58 AM #15
Edge compressed inwards, how to fix?
Thanks guys. Think I’ll bring them into the shop if that is the proper fix, I don’t trust my skills and I really hope I can keep these skis in the rotation for a few more years.
Tuco- interesting theory, didn’t think of that. It’s been a bony year in NE, as usual, so I’m constantly checking for damage throughout the day. I am sure this happened from either the last few runs of the day, or somehow in my ski box on the way home (?). Toward the end of the day were some mega wind gusts coming through that were flinging the skis around our Gondi cabin ski rack, it was so bad that we unloaded at mid-mountain station and brought our skis into the cabin for the rest of the ride. Maybe it happened then by slamming against another ski, or the skis themselves slamming into each other? But if I were forced to guess, I honestly think I just schussed or aired into a rock from the side in a tight situation in the trees.
-
01-09-2020, 09:31 AM #16
-
01-09-2020, 10:54 AM #17Hucked to flat once
- Join Date
- Oct 2005
- Location
- Idaho
- Posts
- 11,001
I’d take that ski in for a grind to get it flat and that’s about it with it only being a rock ski. Or depending how frugal you are and if it’s truly a rock ski, I’d sand it flat at home. Cutting out edges and base material and replacing it won’t be any stronger than thinner base there. If it starts getting too thin, you can cut it out and replace any way.
Keep it simple for rock skis.
-
01-09-2020, 11:25 AM #18
It'll grind through to the edge tab that is bent up(the bubble). Edge does not need to be cut.
Cut out damaged base(cut base &patch @ same time, clamp peependicular to running surface @ bent edge area, tap edge straight. Clean all surfaces and flame treat base material epoxy it, put in patch and clamp that shit with a little heat blowing on it while curing.
-
01-09-2020, 11:28 AM #19
Edge compressed inwards, how to fix?
Thanks guys. I don’t have all the tools and I’m a milennialoser with my hands compared to you lot, working on that. Will report back with the shop recommendation
-
01-09-2020, 11:52 AM #20Hucked to flat once
- Join Date
- Oct 2005
- Location
- Idaho
- Posts
- 11,001
Might hit the tab, might not. I’d still hand sand it a little. If you get in to the tab, go with what you recommend. If it gets flat enough to ski, throw some wax on it.
If those were my rock skis, I’d put a piece of 4x4 under the damage and whack the trouble spot with a 2 lb mallet and go skiing.
If they were not rock skis, I’d put more time into a repair.
-
01-09-2020, 12:01 PM #21
To each their own I guess. You still have a delam in that area.
-
01-09-2020, 12:22 PM #22Hucked to flat once
- Join Date
- Oct 2005
- Location
- Idaho
- Posts
- 11,001
Still a rock ski. I agree with your fix...I'm just lazy when it comes to skis I don't really care about.
-
01-09-2020, 12:23 PM #23
Edge compressed inwards, how to fix?
These are rock skis but I consider all skis shades of rock skis. These are the kind I’m hoping to still be riding 3-4 years from now if possible. They’re only rock skis because I got them cheap, they’ve been really durable IME and they’ve got a bunch mounts. This is the only real issue they have besides the holes.
-
01-09-2020, 12:29 PM #24Hucked to flat once
- Join Date
- Oct 2005
- Location
- Idaho
- Posts
- 11,001
Then Tuco has the fix.
-
01-09-2020, 12:32 PM #25
Thanks dewds
Bookmarks