I successfully taped and used 1/4-20 nylon screws as fillers on such fuck ups. See if you can use the binding and a bushing(hose) on the drill bit to re-drill. Those nylon screws are surprisingly...

5/32 drill bit and pneumatic tubing as drill bit bushing. Almost idiot proof. https://uploads.tapatalk-cdn.com/20230222/7937f1ca940766b1b907c1755f8c731a.jpg

Printing on a transparency film is so...

+1 to dental syringe. Epoxy does not stick to it so it can be re-used.

I filled edge coreshots with g-flex, then just as it began to set I covered it with ptex. It worked.

I have had just epoxy in a hole I drilled though for years, but you probably aren't here for an easy answer.

This thread had great tips for reassembling my Ikea bed for the 5th time. G-flex, bamboo skewers, and steel wool resulted in no spinners or pullouts and a very solid feel.

Daaaamn those are sweet. Does anyone know what is the OD of the #6 from the Bosch kit?

I thought I was a genius when I made my...

Whatever you do will be weaker than it is now. It's a good mount, enjoy. If anyone notices tell them you mounted your own fucking bindings.

Sent from my Pixel 5 using Tapatalk

1. The installation process is the same as BF/QK. Same drill bit and tap.
2. The internal ⌀, external ⌀ and length are the same as BF/QK
3. No, but I can take some as I have to fix my rushed...

Here are some cheap M5 inserts with 5/16-18 external thread. The end is not closed. I just dip the screws in pipe dope, which seals and acts as vibra-tite. They are reasonably corrosion resistant,...

You might want to run the ski through a planer first... or not.

Sent from my Pixel 5 using Tapatalk

I put new tyrolia demo bindings in old tyrolia demo holes. Dunno exactly what is the difference but hole to hole it was probably around 2. I'm sure there's plenty of botched installs that are o6f by...

Oh yes you made those sweet jigs. I will have to figure out how to change yours to the vario 2.

I guess another option would be to use a burr with a drill press. Those should not deflect.

Sent...

Anh tips for preventing drill bit drift in overlapping holes?

Sent from my Pixel 3a using Tapatalk

Some dynafit boots don't have a center mark. How do I find it?

I have a bunch of inserts that have the same internal/external thread as BFs. They are open ended though. With epoxy at the bottom they should work, no?

I prefer not to have the slot. In concerned the slot would allow water to seep in.

Sent from my Pixel 3a using Tapatalk

What's a good enough glue for mounts and re-mounts that is easy to store and easy to disperse. I use west marine epoxy for mounts I want to be perfect, but I want something that's easier to deal...

So the wardens clearance is definately an issue with the punched khions.

I wonder if I can grind down the toe? Dunno, I rather not fuck up these brand new wardens.

Sent from my Pixel 3a using...

The mercury are within the adjustment range. The khions are the ones that are too tall. They don't have any hard rubber like the mercury. Kinda weird they put the hard rubber on the older...

Yea, the boot touches the binding after it released from the wings. It really doesn't seem to add any resistance to the release.

What do you think about the AFD not having the small gap? It just...

Install manual states that's an issue. https://uploads.tapatalk-cdn.com/20201220/6db7bdc52a966b9fe96a00195cb8d8c2.jpghttps://uploads.tapatalk-cdn.com/20201220/191f207e13084b4e21a92316cbde7382.jpg
...

The wardens don't clear the non punched Mercury either. WTF.
My old tyrolia adrenalin clear the punched khions.

Sent from my Pixel 3a using Tapatalk

Shit the boot was punched too much it touches the binding body. Also the toe does not go high enough to gap the khions :(

Sent from my Pixel 3a using Tapatalk

Anyone have the warden toe adjustment manual?

Sent from my Pixel 3a using Tapatalk

Perfect center with two squares put together. Printed on a long piece of parchment paper with clear gorilla tape on top. Solid reusable pattern, none of that weak paper fuckery. Those skis should be...

That's the cheap Amazon press, no? How is it?

Sent from my Pixel 3a using Tapatalk

Wow, laser printers print on parchment paper.

I took a template, laid the two pages on top of eachother in illustrator, then I cut a 8.5x20" piece of parchment paper and just printed it. Perfect...

Does gflex cure clear?

Well the QK is 45 everything in. Cheaper, and I dont see why helicoils would be better.

What's a cheap way to get some helicoils?

I guess the minimum tooling is the drill and the tap. What size is the drill?

Anyone one what the black screw is compared to the regular silver 12AB
163867

FUCK the FKS brake spring /tantrum

^ wait, how many poles do you use with a monoski? 1,2,4?

Walk away. The adrenalins are finicky and a stupid shop can really fuck up. Watch out if you use the supplied template, the creases can move the plates from where they should be. I would print a new...

I know we are the best fucking DIYers on the planet, but maybe we should start a fuck up thread for laughts.

The black fabric pulls off the skin and there is glue underneath. Not sure why BD puts...

Cut my skins... same edge twice. http://img.tapatalk.com/d/14/01/14/e5ateqy9.jpg

Good tips thanks.

I think a drilling block will be key here. I can clamp it, and maybe even use a sheet of rubber between the ski and the block. That will keep the bit exactly where I want it.
...

Anyone drill overlapping holes in skis with metal topsheets? Even with a drill press the bit might bend and go in the original hole, no? I am thinking I should fill the original holes with epoxy,...

Well... I deserve some heavy jonging for my lazyness. I had a shop mount my adrenalins and they fucked up in every possible way. All screws are crooked as fuck. Worst of all the bindings don't lift....

I don't really trust a drill press depth adjustment. I rather use a shoulder on the bit.

CA=cyanoacrylate ?

Doese't it dry quicly? How would the wood absorb it? How is it better than epoxy?

West germany... I guess these aren't flying off the shelves.

http://img.tapatalk.com/d/13/01/17/u3etytan.jpg

Thanks, I looked for wiha screwdrivers after I saw one of my colleague's, but I misspelled the name. Their robbies are amazing.