I don't know the answer to your question - but there's an easy answer.
Grab both templates (demo and non-demo) and print them both. Exacto out one of the templates holes (With thin paper and some...

Thanks! Added to the first post.
[And nothing to be ashamed about a pair of HF calipers. I have a pair myself. I can't justify spending more, and they do more than adequate service for what I need.]

I just added screw measurements for the Attack1/2 Toe and the Attack2 heel.
I don't have an Attack1 heel here to measure.

If someone has the Attack1 demo heel floating around, could you measure...

Shows up just fine for me on the Mac+Safari.

See this post:
https://www.tetongravity.com/forums/showthread.php/304091-Tyrolia-Attack-13-Demo-paper-template?p=4808065#post4808065
Go to the BOTTOM...

If you're using a phone or tablet, open the site in "desktop" mode - at least that's what Chrome/Brave calls it.

In mobile mode, you can't see the "attachments" that have the PDF template. The...

Sorta a recommendation on MRR11's idea.
But I'd simply print the template up at the top there.

Cut it out and mark the centerline of the ski. Now just lay the template on the ski, where you'd put...

I have not compared a regular Attack mount to a demo mount - but I think the heel would almost never go in the same place, in relation to boot center for a non-demo vs demo. [I suppose for the right...

^^ That's an Attack demo, it looks like. The Attack2 is AT/MNC.
The two demo bindings have the same mount pattern. [the toe rail is exactly the same for both - you can slide on an Attack2 toe on an...

Dude, it's kind of like I posted a "how-to" to change the head-gasket on a Subaru.
Then you post; "Ya know, this how-to doesn't work for my Buick. People should be warned!"
And you attach a...

Sigh.
@SoooL
Look at that template picture.
Now compare to the template posted at the top of this thread.

Not. the. same. template.
As noted in the post you just posted after - this is for a...

Since I'm the OP - I'm going to pipe in a bit.
1) "... I assembled the templates for the correct BSL's..." I'm not sure how that's possible for a demo binding. There's simply a single line ["Boot...

So, I have an attack2 demo in hand, and all measurements certainly seem to show that this template is unchanged for the Attack2 13 *demo* [I have no idea about the non-demo layout.]

When I get a...

The template above is correct. I [and others] have mounted the demo binding and 42mm is simply not right. I have no idea what any older binding may have used, but it's obvious, looking at the picture...

See first post in the thread. [Addendum at the bottom.]
Updated template with the proper 43mm rear-screw width on the heel piece.

I was going to attach the template again, but since I updated it...

@Chaka, @Core Shot:
I emailed Knut, but no reply.
I guess I'd suggest that people use my less than pretty template until Knut fixes the PG one.

-Greg

This looks like the Attack 13 NON demo template...
http://www.powderguide.com/community/forum/get_attachment/anhang111.html

[I found it listed at Slidewright here:...

Emailed Knut - lets see what he says. [I have no idea about the non-demo version.]
I got the measurements for my template by using calipers against an actual binding. Then, eventually, I got the...

I've never done a mount using the PG template. [His templates are totally wicked, BTW - they look so good, and the ski centering guide is the bomb too.]

Anyway - I too thought that 43mm was a...

NOTE THIS IS FOR A DEMO BINDING ONLY!
(Yes, it says that everywhere, but you'd be surprised how often people don't read and then complain about it being wrong, etc.)
The template should be good...