Search:
Type: Posts; User: Alpinord
Search: Search took 0.02 seconds.
-
02-29-2024, 05:17 AM
- Replies
- 611
- Views
- 175,077
Yes and use your boots to verify alignment. I...
Yes and use your boots to verify alignment. I redrilled some ION holes for inserts and had one off a skootch. By sequencing the tightening I used the other three holes to align the wonky one. Worked...
-
12-27-2023, 08:09 AM
- Replies
- 611
- Views
- 175,077
Nice job. Good to hear feedback.
Nice job. Good to hear feedback.
-
12-24-2023, 07:36 AM
- Replies
- 611
- Views
- 175,077
Thanks Thom. The insert tool is based on the jam...
Thanks Thom. The insert tool is based on the jam nut technique, but easier & quicker. It also works for both Binding Freedom inserts & Quiver Killers.
Along with the good reminders on cleaning... -
12-23-2023, 06:16 AM
- Replies
- 611
- Views
- 175,077
Review: Binding Freedom Inserts - The Swiss Cheese Experiment
After filling the hole you could drill for an alpine screw in the errant hole first, with inserts in the others for now.
I have yet to see or hear about the 5/16” tap being too small. The thread... -
12-22-2023, 09:28 PM
- Replies
- 611
- Views
- 175,077
(For the next time, drill for alpine screws...
(For the next time, drill for alpine screws first, test drive, THEN install inserts.)
Sizing, a 1/4” bit is a little smaller than an F bit, which is the ‘spec’d’ size for BF inserts, but 1/4” is... -
11-14-2023, 03:44 PM
- Replies
- 611
- Views
- 175,077
Reprint at ~104%. (66mm/63.53=1.0389)
Reprint at ~104%. (66mm/63.53=1.0389)
-
11-10-2023, 09:01 AM
- Replies
- 611
- Views
- 175,077
The idea of grinding the tip of a wide...
The idea of grinding the tip of a wide screwdriver is so the thickness fits the Binding Freedom insert slot better. An 8mm hex bit works too:
... -
04-11-2023, 09:04 PM
- Replies
- 611
- Views
- 175,077
A bigger hammer. :D How far off are you and...
A bigger hammer. :D
How far off are you and how many of the holes are off? In some cases, if off a skootch, you can force the odd insert laterally vs needing to redrill. If most of the holes are... -
02-12-2023, 09:02 AM
- Replies
- 611
- Views
- 175,077
Review: Binding Freedom Inserts - The Swiss Cheese Experiment
This deep:
447422
“Both Quiver Killer and Binding Freedom inserts are nominally 9mm length x 8mm (5/16″) diameter. The actual diameters for both average 7.85 mm. The lengths QK inserts average... -
01-30-2023, 11:30 AM
- Replies
- 611
- Views
- 175,077
FTR, BF=SVST. Sourcing heli-coils and their tools...
FTR, BF=SVST. Sourcing heli-coils and their tools gets spendy complicated vs simply using Binding Freedom/stainless steel inserts, IMO. YMMV.
Though I have a good memory, but it's short, IIRC, the... -
12-28-2016, 09:29 AM
- Replies
- 611
- Views
- 175,077
^^^^^ Good point. (Pun intended). Regarding...
^^^^^
Good point. (Pun intended).
Regarding machinable epoxy, (test this first) you may be able to install the insert (or screw) with machinable epoxy and remove the insert (or screw) after it... -
12-28-2016, 07:08 AM
- Replies
- 611
- Views
- 175,077
FWIW, if you do strip the threads, all is not...
FWIW, if you do strip the threads, all is not lost. You can use machinable epoxy, cure, re-drill and re-tap to repair.
-
11-25-2015, 05:01 PM
- Replies
- 611
- Views
- 175,077
An 18mm smallhead that you'll need, measures 20mm...
An 18mm smallhead that you'll need, measures 20mm total length. The smallheads are like a flat head (measured/usable length) PLUS 2mm for total length. The critical measurements are where the screw...
-
11-25-2015, 05:41 AM
- Replies
- 611
- Views
- 175,077
IIRC, basically since 2010 they should be the...
IIRC, basically since 2010 they should be the same. The image looks exactly like some black and white FKS's we just mounted.
Here are some tips on Measuring Screws.
BTW, I just read that Look... -
11-30-2012, 09:27 PM
- Replies
- 611
- Views
- 175,077
Or use a drill guide or a washer in a pinch.
Or use a drill guide or a washer in a pinch.
-
04-28-2012, 09:19 AM
- Replies
- 611
- Views
- 175,077
As do chain cleaners, citrus degreasers/wax...
As do chain cleaners, citrus degreasers/wax removers and even Dawn dish soap.
-
02-29-2012, 10:56 PM
- Replies
- 611
- Views
- 175,077
Is the height due to not enough depth drilling or...
Is the height due to not enough depth drilling or during the insert install? If the former heat, extract, redrill, re-tap (may not be necessary), re-epoxy and install. If the latter, heat and drive...
Results 1 to 17 of 17