Dee Hubbs
Registered User
Find latest postsMini Statistics
- Join Date
- 01-29-2008
- Last Activity
- Today 11:37 AM
Recent Visitors
This page has had 357,687 visits
- Tab Content
- Dee Hubbs's Activity
- Visitor Messages
- About Me
-
Older Activity
-
Today, 10:49 AMThere are some neighbors you don't lend any tool too. XXX-er i'd lend you my tools any day.4797 replies | 954450 view(s) -
Today, 10:35 AMWhen a customer use to argue about what +3 from recommended means, I'd say something just like this, then draw it on a piece of paper for them....4797 replies | 954450 view(s)
-
Today, 10:06 AM100 replies | 6959 view(s)
-
Today, 09:46 AMThe points I made in my Ticket to Zwift are: -I log in warm up in another world, all sensors work. -Join the meetup 5 mins before start (my...1458 replies | 354808 view(s)
-
Today, 09:38 AMIf you think Vail Mountain can handle 55,000 visits in one day, your smoking crack! The daily max is less than HALF of that, more like 38% of that...100 replies | 6959 view(s)
-
Today, 09:33 AMNobody care that you tele! FIFY: Nobody cares what you say.100 replies | 6959 view(s)
-
Today, 09:22 AMAlso one of these sleeves also would work on your dropper. The stanchion on most droppers is either 25mm or 26mm (I cant remember the Lev's...18 replies | 2503 view(s)
-
Today, 09:17 AMThat silver square goes inside (and against the bar) the open cutout on the above clamp. Also if you have sram brakes, that clamp can replace the...18 replies | 2503 view(s)
-
Today, 09:10 AMI'm pretty sure I'm not getting a draft when I'm invisible. It says "close the gap" but during these "invisible meetups" my rider never goes from the...1458 replies | 354808 view(s)
-
Today, 08:54 AMI was ahead on the flats after the climb, and let off the gas just a little bit to regroup, and the group blew by me (invisible me) so I busting my...1458 replies | 354808 view(s)
-
Today, 08:39 AMMy apple TV and iPhone are set for auto updated. I know it updated after the Jän 21 update, but no AppleTV are available yet. But I'll force load...1458 replies | 354808 view(s)
-
Yesterday, 09:54 PMLet me look tonight, and see what I have. I should be able to find what you need, and do a local meet up.2 replies | 534 view(s)
-
Yesterday, 09:40 PMHopefully Mikaela won't fall deep into the world of hookers and painkillers.1730 replies | 293984 view(s)
-
Yesterday, 08:20 PMI did a full lap and couldn’t hold on. Something is wrong. I’ll put in a ticket. Butta: Thursday invite just went out.1458 replies | 354808 view(s)
-
Yesterday, 08:12 PMI’m seriously asking? I’ll put a ticket in to Zwift help.1458 replies | 354808 view(s)
-
Yesterday, 08:09 PMI was seriously not there? I thought you guys were joking with me? I fell off the back, like 3 seconds and could not catch up even when the draft...1458 replies | 354808 view(s)
-
Yesterday, 07:49 PMSome late joiners and early departures. VTskibum (M.P.) early leaver Dee Hubbs (D.H.) fell off the back, went for early dinner, sorry ...1458 replies | 354808 view(s)
-
Yesterday, 03:32 PMThat sucks. Because if it was lever clamping, I would have suggested just leaving the full length cable coiled by the lever and just un-pinching it...18 replies | 2503 view(s)
-
Yesterday, 12:40 PMThe Ritchie disconnect will not work, it needs tension between two cable housing stops. What dropper/remote do you have? Does your dropper remote...18 replies | 2503 view(s)
-
Yesterday, 10:43 AMMikaela is 25 years old, and will turn 26 at the end of this ski season. She has: 68 WC wins 100 Podiums 3 Overall Globes, 7 Small Globes 11...1730 replies | 293984 view(s)
-
02-22-2021, 07:35 PMThey make an adjustment plate for these, can adjust 20mm.2 replies | 1017 view(s)
-
02-21-2021, 12:50 PMSkimo sells aftermarket titanium binding screws for its race weight weenies. Many low tech race bindings come standard with Ti screws.55 replies | 8336 view(s)
-
02-21-2021, 12:39 PMAnd if you're in the group draft, your lap time will be quicker. The draft will not reduce your work/power output. The draft will just make you go...1458 replies | 354808 view(s)
-
02-20-2021, 08:40 PMYou wrapped them upside down, the taped in overlapped in the wrong direction. You should go from the bottom up, so your seams won't roll over with...53 replies | 8638 view(s)
-
02-20-2021, 06:54 PMI get more worked up trying to order takeout. Pilot: “gonna need a turn immediately” Me ordering take out: “Are you sure got the spring rolls?...122 replies | 14598 view(s)
-
02-20-2021, 04:40 PMThe JIS specification for screws/screwdrivers is longer an active standard, and has been absorbed into the current DIN 5260-ph (DIN is the Deutsches...55 replies | 8336 view(s)
-
02-20-2021, 04:00 PMWhole different thread!55 replies | 8336 view(s)
-
02-20-2021, 03:34 PMYou sometimes hear they called "SquareHead deck screws". But not very common. With the recent popularity of Torx, they are used more in construction...55 replies | 8336 view(s)
-
02-20-2021, 03:23 PMHenry Ford offered to buy Robertson's patent for use on the automotive assembly line, but he was un willing to sell the patent. The recently...55 replies | 8336 view(s)
-
02-20-2021, 02:54 PMThe Imperial Century was in the back of my mind too. After getting the free miles downhill from AdZ, then it’s pretty close (another 18-19 kms) and...1458 replies | 354808 view(s)
1 Visitor Messages
About Dee Hubbs
Basic Information
About Dee Hubbs
- Location:
- BC to CO
- Sport:
- Skiing
Statistics
Total Posts
- Total Posts
- 3,041
- Posts Per Day
- 0.64
Visitor Messages
- Total Messages
- 1
- Most Recent Message
- 02-13-2014 12:20 PM
General Information
- Last Activity
- Today 11:37 AM
- Join Date
- 01-29-2008
