Results 1,076 to 1,100 of 1728
Thread: Binding Mount Paper Templates
-
01-03-2017, 09:05 PM #1076
Rossignol/Look Jr Bindings Template?
I have been searching the inter-web to no avail for a paper template for rossi/look jr bindings. Specifically I have some Look Team 4 JR QS bindings I'm hoping to mount. Anyone have a template?
-
01-12-2017, 10:39 AM #1077
Isn't that the same mounting pattern as all Jester/Griffon/Squire/Lord? They all have the same mount pattern for normal/schizo/demo, just that the demo gets mounted for BSL 315 to fit all boot sole lengths. If you intend to use it to adjust your midsole position, just shift toe/heel unit accordingly.
There is a newer version of that file including more binding templates to be found here under the link "Vergleich der Bohrlochpositionen für verschiedene Bindungen": http://www.powderguide.com/community...8d8abab15c36a5
(My apologies for not hotlinking it directly, but then the link would get broken the moment I update the file)
-
01-13-2017, 02:54 AM #1078
^^^^
Hey Knut,
Just a heads-up on your template for the Beast 14. The spacing between the back two holes should be 36 mm instead of 38 mm. I mounted up a pair with that template last night and everything else is dead on with that modification to the template.
Merci vielmal!!!
-
01-13-2017, 04:40 AM #1079
Thanks mate, feedback is always much appreciated (and much needed). I will look into it and change the template accordingly. Fine-tuning the beast templates has been quite a nuisance with conflicting infos. I think I went from 36mm up to 38mm for those holes due to user feedback at one point.
How about boot centre? Did that turn out right? Did the heel end up in the middle of the track? (That's normally the most imprecise part of making a template)
-
01-16-2017, 04:03 AM #1080
-
01-16-2017, 07:41 AM #1081
Thanks again. Template with the change from 38 to 36mm is up (also because two more people suggested it on the German forum).
-
01-17-2017, 05:43 AM #1082
-
01-19-2017, 04:35 AM #1083
Does anyone have the new Rossignol SPX templates?
I Came, I Saw, I .... Made A Slight Effort & Then Went Home For Lunch.
-
01-19-2017, 06:51 AM #1084
I haven't seen one on the webs yet. The heel pattern has changed in comparison to the Axial2, correct?
If you'll measure it, I'll make a template, no problem.
-
01-19-2017, 10:50 AM #1085I Came, I Saw, I .... Made A Slight Effort & Then Went Home For Lunch.
-
01-22-2017, 08:42 PM #1086
I have a small suggestion for the templates. If the scales on each half templates had numbers facing each other (e.g. left for the top, but right for the bottom) it would be super easy to assemble the templates by cutting along the black line and matching numbers against each other.
-
01-24-2017, 02:51 PM #1087
Created a Vipec template due to minor errors I found in the PowderGuide and Dawson templates (Spring of 2016). Perhaps they fixed it since then, but I've used my template for two mounts.
I published details (and PDF download) in the Vipec thread (post #472): http://www.tetongravity.com/forums/s...67#post4917867
Cheers,
ThomGalibier Designcrafting technology in service of music
-
02-03-2017, 06:39 AM #1088Minion
- Join Date
- Feb 2017
- Posts
- 1
Templates: Warden 11 Demo - warden 13 Demo
Where can i find paper templates for Atomic warden 11 demo and Atomic warden 13 demo?
The Salomon rental template is not the one.
Anyone knows?
-
02-11-2017, 08:42 PM #1089
The markerfit template isn't on bindingfreedom's website despite the other plates being on there. Is the template here correct?
But Ellen kicks ass - if she had a beard it would be much more haggard. -Jer
-
02-11-2017, 08:44 PM #1090
-
02-11-2017, 09:58 PM #1091
If by 2X4 you mean sexy praxis Quixotes then I will.
But Ellen kicks ass - if she had a beard it would be much more haggard. -Jer
-
02-11-2017, 11:38 PM #1092
Markerfit template works.But Ellen kicks ass - if she had a beard it would be much more haggard. -Jer
-
02-11-2017, 11:55 PM #1093
Sick!
-
02-12-2017, 12:20 AM #1094
Damn fine looking skis
Now I won't be the only one with Praxis that are side specific
-
02-12-2017, 02:37 PM #1095but not a marker fanboy
- Join Date
- Apr 2012
- Location
- N@
- Posts
- 394
Just a heads up on the Tyrolia template, and this was first mentioned a few years ago in post #788, but the template seems to put you in front of the line, at least for smaller boots. Mounted a pair of Padlock 11s for the wife a year or two ago for a 285 bsl, mondo 24.5, and it ended up being about 5mm ahead of the line and the heels were all the way to the front of the track with correct forward pressure. Was really pissed I didn't do a test mount on those but figured maybe I accidentally mounted for a 295 bsl since that's my boot size, especially since the mount was right on the line and in the middle of the track if adjusted for my boot.
Fast forward to today when I did some test mounts for an Attack 16 using my 295 bsl. Same thing, put me way forward of the line, about 1 cm. To properly adjust for my 295 bsl to be on the line and the heels in the middle of the track, I needed to put the toes for a 282.5 bsl and the heels for a 307.5 bsl.
Just be sure to test mount before using this template and confirm it's putting you where you want to be relative to the line.
-
02-13-2017, 06:39 PM #1096
Looking for a Marker titanium 1200 template. Any help out there?
I've concluded that DJSapp was never DJSapp, and Not DJSapp is also not DJSapp, so that means he's telling the truth now and he was lying before.
-
02-14-2017, 07:08 AM #1097
-
02-23-2017, 03:28 PM #1098
No changes to the hole pattern based on my recent swapping around of current and former Rossi and Look bindings, therefore:
Rossignol Axial2/SPX/SPX WTR = Look PX10/PX12/SPX/SPX WTR
Do note that screw lengths have changed for the new SPX bindings. However, brakes remain interchangeable.Last edited by critical-motion; 02-23-2017 at 03:42 PM.
-
02-27-2017, 07:30 PM #1099Registered User
- Join Date
- Oct 2016
- Posts
- 66
I've been a bit well, skeptical, after reading this thread of mounting with a paper template. Are these things ever reliable? I feel like pretty much every template you guys are talking about is all screwed up or off on some way not making it mountable without some pretty nice adjustments. Am I wrong, or is it pretty easy to do these adjustments without a huge risk of screwing it up.
-
02-27-2017, 08:18 PM #1100serial lurker
- Join Date
- Feb 2006
- Posts
- 309
It all depends on you. Are you capable of setting things up, testing it out, double checking and then drinking a beer and mounting; or should it just work perfectly with no thought or input on your part? If the latter, find yourself a 'professional' and pay them for their gumption in performing the prior.
Bookmarks