Results 1 to 9 of 9
-
05-10-2016, 10:08 AM #1Gel-powered Tech bindings
- Join Date
- Dec 2004
- Location
- Amherst, Mass.
- Posts
- 4,684
Identify this pull-out kitchen trash bin design?
Okay, so this is rather unlikely, but .... anyone able to identify the manufacturer of this pull-out kitchen trash bin design?
The sliding rails have become all mangled (which isn't all that bad a track record after a full decade of sliding in & sliding out).
Since all the components are separate, would be really easy for me to replace, except ... I can't find any identification of the manufacturer on the various parts, our house's construction manager has no idea, the cabinet company says its not their design, and everything I've looked at in person and on the web is a different (and incompatible) design.
Failing that quest, any recs for a complete replacement?
Thanks in advance for any helpful feedback, and congratulations in advance for anyone who can think of some humorous commentary.
Mo' skimo here: NE Rando Race Series
-
05-10-2016, 12:50 PM #2Registered User
- Join Date
- Dec 2009
- Posts
- 946
not sure if it came from there but Hafele makes a lot of fittings like this, if not you could certainly replace it with something from there. might be tricky to buy retail but it should not be impossible to find or order:
https://www.hafele.com/us/en/product...178c395baedfb/
-
05-10-2016, 01:37 PM #3
also check out rev-a-shelf
http://www.rev-a-shelf.com/catalog/d...Containers.pdf
-
05-10-2016, 08:30 PM #4
Jonathan, are you serious?
This is what I have, stick a paper bag in it each week:
http://www.aristokraft.com/products/...movable-hamper
-
05-11-2016, 04:13 PM #5
I can't see the details well but it looks like any full extension drawer slide would screw onto the bin. Take the rails off, go to HD or Lowe's and see if you can't find a slide whose holes match up with the holes in the bin. Something more heavy duty will last a lot longer than 10 years.
-
05-12-2016, 05:42 PM #6
What ? .... no one posted Praxis RX ?
-
05-12-2016, 06:42 PM #7
-
05-14-2016, 04:44 PM #8Gel-powered Tech bindings
- Join Date
- Dec 2004
- Location
- Amherst, Mass.
- Posts
- 4,684
The problem is that the cabinet door is connected to the entire assembly.
And that part of the cabinet has both the recycling bin and the trash bin.
So the only way to access both bins is to place the recycling bin just barely inside the open cabinet, and keep the trash bin on the floor in front of the open cabinet, as shown below.
Which isn't the most horrible temporary solution, but I'd like to fix it eventually.
(Especially since I don't have any ski projects at the moment, except for mounting up three pairs of rando race skis soon....)
Ah, okay, will look into that, thanks.
But how will they do if I mount them up with these bindings?
http://skimo.co/dynafit-rc1-bindingMo' skimo here: NE Rando Race Series
-
10-09-2016, 09:12 AM #9Gel-powered Tech bindings
- Join Date
- Dec 2004
- Location
- Amherst, Mass.
- Posts
- 4,684
So my project this morning reminded me of this.
I had looked into replacing just the slider hardware:
http://www.rockler.com/hardware/drawer-slides
... but compatibility was confusing.
Ended up going with this:
http://www.kitchensource.com/trash/ha-502.56.880.htm
Alignment was relatively easy, and works very smoothly overall.Mo' skimo here: NE Rando Race Series
Bookmarks