Results 26 to 47 of 47
02-06-2012, 02:02 PM #26who turned up da gravity?
- Join Date
- Dec 2011
02-06-2012, 04:56 PM #27Registered User
- Join Date
- Nov 2003
Solid offering, Jon!
Congrats!Aggressive in my own mind
02-06-2012, 08:38 PM #28
02-07-2012, 12:06 AM #29
02-07-2012, 12:13 AM #30
So, simplistic as i am, i take it the dynalook doesn't share any holes with the dynaduke and I would have to re-drill?Our world is full of surrender at the first sign of adversity, do not give up when the challenge meets you, meet the challenge. Through perseverance comes the rewards, the rewards that make life so enjoyable.
Seize the day, trusting little in the future.
if you want something, go after it. if you want to screw someone over, look DEEP in your heart and realize Karma is a bitch
02-09-2012, 12:47 AM #31
^^ sorry - I didn't answer your question at all.
DynaLook toeplates share the two frontmost holes with Dynadukes, but the rearmost holes are 20mm further forward. (Toes: reuse 2 holes, fill 2 holes, drill 2 new holes)
DynaLook heelplates share their rear 4 holes with DynaDuke holes only for 320BSL & Large, or 280BSL & Small. (Heels@320or280: reuse 4 holes and drill 2 new holes; Else: fill 4 holes, drill 6 new holes).
02-09-2012, 11:11 PM #32
The hotness. I still need a real camera.
The templates are a little off, but using the existing holes for the plums it took about 20 minutes to set it all up. It was also pretty easy to set the up to run 2 boots with different BSLs - 310 on the full tilts and 318 on the factors.
I could basically sell all my other skis/bindings with this setup, if I wasn't such a gear whore.
Jon, you're the man.No, the real point is, I don't give a damn
02-09-2012, 11:51 PM #33
FKN awesome. stoked for these!
02-10-2012, 09:57 AM #34**
I'm a cougar, not a MILF! I have to protect my rep! - bklyn
In any case, if you're ever really in this situation make sure you at least bargain in a couple of fluffers.
02-11-2012, 07:51 AM #35
gotta ask jondrums, is the mount consistent with other BF plates. may pull another auction for my dyna/duke lhasa's if I can get a pair of looks on there?
02-11-2012, 07:53 AM #36
duh, sorry just saw the post above. need coffee
02-13-2012, 02:15 PM #37
Bump for awesomeness. Just ordered mine.
03-03-2012, 11:52 AM #38
Hey Jondrums, if using with PX/Axial 2 and Dynafit (not FKS), can you get away with only drilling the back 4 holes on the heel plates?
04-27-2012, 10:19 PM #39
05-09-2012, 09:44 PM #40
05-10-2012, 08:35 AM #41
05-10-2012, 01:52 PM #42Registered User
- Join Date
- Apr 2004
05-10-2012, 02:35 PM #43
Last edited by Bird Blaster; 05-10-2012 at 03:06 PM.
09-07-2012, 04:47 PM #44
Sort of just realizing this now... is it possible to have the plates for two skis and swap out an FKS binding for a 306 BSL and then swap in some Radicals that will use a 287 BSL?? Hmm... suppose FKS at neutral and the Radical has a 25mm of adjustability would work out
Last edited by StopMakingSense; 09-07-2012 at 08:01 PM.If you can't dig it, you ain't got no shovel
01-07-2013, 08:40 AM #45
Assuming this is the case you would end up with half of the dynafit 25mm or 12.5mm of adjustability and I need ~17mm (313-296=17).
Soo, if my assumption is correct, could I mount my plates at something like 307 since FKS has 10mm of adjustability and dynafit has 12.5 in the opposite direction.
One more catch: Moment recommends -5 mount and the skis will be used with the dynafit 75% of the time.
Huge thanks to anyone that can answer this, my skis are in the shop and I need to get this right!!
01-07-2013, 11:48 PM #46
^^ yeah, its a bit tricky. I'd def. suggest a test mount first with that much difference between them.
StopMakingSense needs to mount for 299 without much margin.
skialpy, try 306 @ -1cm (puts 296bsl @ -5mm and 313 @ -13mm)
I think FKS has +/-7, and dynafit +/- 13
01-08-2013, 11:22 AM #47
Thanks Jon! This tlt5 boot is throwing a wrench in my plans. Not sure I want to ski at -13 so the deliberation continues. Thank you for responding and making an awesome product!!